1985816150 Kenmore Freezer - Instructions

Followed web instructions.

I checked the inlet hoses for hard water build up and noted that this was not a problem. Then checked the hose from the inlet valve to the washer drum and determined that it was clear so I knew the problem was a faulty inlet valve. After receiving my replacement valve, I removed the old valve by removing the hot and cold water hoses and unscrewing two screws securing the inlet valve and lifting the inlet valve out the metal holding bracket. This gave me complete access to the inlet valve allowing me to remove the hose clamp and hose to the washing machine drum. The new inlet valve was an exact match so I removed the four electrical wires one by one while putting them back on the new inlet valve to insure correct electrical connections. I added a piece of one half inch plastic tubing provided with the new inlet valve on the outlet nipple of the new inlet valve to prevent leaking. I then put the new inlet valve back into the holding bracket and screwed it down. I replaced the hot and cold hoses to the new inlet valve carefully so as not to cross thread the plastic connection on the new inlet valve. After turning the water back on, I checked for leaks and plugged the washing machine back on to test it with a washing cycle.

Removed old valve and replaced with new. Wire for wire..screw for screw..

Washer is enclosed in a walled partition. I spent more time moving the washer out so I could get to the back of the machine. Due to Maytag's design of a removal sheet metal panel holding the valve the entire water valve replacement was performed outside of the machine. The replacement valve was an exact duplicate and made it a simple swap out. More time was spent removing inlet hoses and outlet hose then in actual valve replacement.

First turned off water and unplugged washer. Removed hoses and then removed bracket. The new part needed the bracket from the old mixer which was no problem - 3 screws. Removed electrical plugs from old mixer-placed on new one.No problems - worked like new. Thanks for your prompt shipment and the good illustrations of the parts when I was searching.. Also, half the price of local parts houses and it would still have to be ordered.

Removed old part, installed new part. tested machine. worked fine.

The repair was simple, and followed the instructions exactly. Removed three screws, one small hose clamp, and two electrical connectors. Replaced and reassembled. Worked like a champ!

The hot water side would fill quickly but the cold water filled very slowly. The seloniods and the valve is built all into one unit. I ordered and replace the part in no time at all. Now both hot and cold water fill quickly.

open top of washer
remove two screws that hold water inlet valve
disconnect four wires and hose;replace new water inlet valve and reversed operation
everything went well

Removed door panel to get to the electric control conponents and noticed a burned wire to one of the door microswitches. Ordered the door switch repair kit from PartSelect. Also, ordered and replaced the thermal fuse at the same time since it was only $12 and didn't know if that blew at the same time the switch cooked. I had the parts coming standard delivery (3-5 days), but they arrived the very next day. Parts included easy to follow directions.Job went pretty smooth and the dishwasher works again Good experience!

Shut off water supply, unplugged washer power, removed supply hoses from old washer valve assembly, removed valve mounting plate and removed old valve assembly from mounting plate, diagrammed and disconnected hot and cold solenoid valve wiring and removed valve assembly outlet hose. Installed and connected new valve, performing the preceding steps in reverse order. pressurized new valve, verified valve function and checked for leaks and placed washer back in service.

Solved theprobel m by noticiing the HOT water filled the tub and it began to run when it was full. Figured out it was the solenoid valve. Ordered a new one. Simple to install and then it ran just fiine.

Did the same as others. Loosened the three screws diconnected the wires and put them on the new valve. Disconnected fill hose and connected to new valve. 10-15 minutes. Replaced panel and tested new part. perfect, My repair was a little longer, I vaccumed up all the dust bunnies I could find before moving washer back. Good for another 35 years, I hope. Thanks for the help and experiences.

Pushed machine out from wall; disconnected the supply hoses (after closing the valves at the wall); unplugged electrical cord; removed two wires from the solenoid connectors; removed two screws that secure valve assembly to backplane of machine. Installation of new assembly was the opposite procedure. We have private well, and silt was plugging the cold water side of valve. So, I also installed a large sediment filter behind the washer, so this will never happen again.

Took out 2 5/16" screws and loosened top and took off two ground wires and 2 hot wires for cold & hot water solenoids and removed & replaced solenoid wires and fill hose. Also Had fantastic delivery of parts.