1067381540 Kenmore Freezer - Instructions

My fridge is a little different from the video model. The Controls in the fridge are located on an "arm" which swings down when the two screws are removed from the sides. It was not necessary to remove a front plate or knobs. However, I found when I got in to it that the old timer was not held by screws, but by plstic posts which had these "speed nuts" on them. This is a little metal plate which fits over the plastic post and bends to lock it in place. When you try to remove it, it acts like a barb, holding the little sucker on. I ended up bending the ends of those little suckers up tight against the post and twisting and pulling with needle-nose pliers. I broke one post like others before me commented, but one stayed intact. The only break at the top, so there ie still post left to hold the new timer. Once it was off, I was able to replace easily. The directions for choosing the right prong were a little confusing, but follow your gut and go with the wire colors. My schematic found in the bottom of the fridge did not look like any of the drawings, but I could match the wire colors. I also asked "Just Ask" for help, to make sure. My gut instinct was right. My fridge is now working again beautifully. If a housewife with no appliance repair knowledge can do it, so can you. I fixed my dryer with PartSelect too!I will never call another repair man until I have checked this site to see if I can do it myself. Bet I have saved $600 so far at least!

First of all the part was not located in the section of the refrigerator that was shown in the video. I wasted a lot of time taking that section apart only to find that the part wasn't there. After some investigation I finally located the defective part. It was behind a piece of sheet metal that had to be bent out of the way to unscrew the part. If I hadn't bent it out of the way, it would have been a major disassembly to remove the sheet metal. Once removed, the installation of the new part was fairly simple. The only confusing thing about the installation was determinig which of the prongs on the part that the internal wire to the new part was to be attached. There were 3 options given and the instructions were not very clear as to which one I should use. Apparently I guessed correctly because the refrigerator seems to be functioning perfectly since the repair.

I just simply eliminated the ice buildup with hot water and a knife. But I still have the Defrost Timer Kit for future use.

My husband put in in, no problem and all is well. My husband is a mechanic for large machinery/motors so installation was no problem. Thanks, better than buying a new fridge!!!

One day the ice cream in the freezer seemed mushy, but the ice was still frozen. There was not water in the ice bin. However, the problem resolved itself. This suggested that the defrost timer had become stuck for an extended time, but then continued to run. The fact that the freezer went back to frozen, implies that all the components of the cooling loop (compressor, condenser & fan, evaporator & fan) were fine. It was possible that the problem was caused by a bad defrost (?evaporator?) thermostat but everything I saw on line suggested that the defrost timer is the culprit about 40 - 50% of the time. Anyway, I followed the instructions in the on-line video at this site for replacing the defrost timer and it was easy. It would have only taken 15 minutes, but I spent a while reading the defrost timer instructions and hunting down a schematic for my refrigerator, to determine which pin the loose wire should go on.

Removed the old fan; cut the wire and spliced in the new fan and reassembled. A little over one hour. Refrig is working perfectly now with lower settings. It is definitely off much more than on now.

just had to remove the fan motor the hard thing is getting down to it

Well I could what laid on the floor and replaced it but I didn't I emptied refrigerator laid it over change the motor then stood it back up actual work about three hours

removed condenser fan -located behind refrigerator next to compressor, Not much clearance to work, there are 3 screws to remove from condensing motor,sounds easy but clearance is lacking to remove them ,(takes alot of PATIENCE). Then you have to remove the fan blades to be able to get clearance to remove motor!! I wouldn't reccommend trying this repair unless you are a pro.

The video of the repair is a helpful guide, but my refrigerator has the compressor very close to the condenser fan motor. With the compressor comes the copper tubing that is all in the way. I had to carefully bend them now and then to allow me to get my hands in position. The how to is easy, but the working with tools in cramped quarters was difficult. I think my Maytag side by side model makes for this job to be difficult, maybe yours may not be so bad. I took a couple of hours to complete. After the first hour, I covered the bare wires, and plugged the frig back in so it could do some cooling. I placed a small in front on the condenser to blow across it. Had a little break, then finished the job.

I have an Amana freeze and I followed the procedure in the video. Which is very good! However on the Amana Model there two slight differences in the procedure that I felt I needed to do. The first one is, the condenser fan bracket is attached to the Freezer chassis with 4 screws, not three. The removal and installation of the back screw by the fan is a bear. I removed the other three and it allowed me to rotate the fan slightly to get more access to the fourth and did same on installation by just starting the 4th screw and then tightening it later. The second issue was my new fan hit the housing when I spun the fan. When I looked at the old one. It had a phenolic washer, between the fan and motor which spaces the fan out about a washer thickness from the motor. When I tried to remove the old one it broke in four pieces due to age. So, I made my own with a washer that I super glued to the motor housing after carefully centering it on and clearing the motor shaft . Seemed to work with out any more noise or balance issues...Thanks, your delivery was blindly fast and video was great!

Took the old fan out and put the new fan in.

It wasn't quite as easy to get to the bolts as the video showed. The lay out of the part wasn't exactly like the video either. However, I managed to put the new part in. Unfortunately, it didn't solve the problem. At first the fridge cycled on and off but after 12 hrs it started to freeze liquids again. Since the appliance was 17 years old we opted to just get a new one.

Pulled the electric plug! Removed the freezer shelf and the rear shelf supports by pulling straight up. Swung rear panel out of the way after taking out the two phillips head screws at the top. Removed the plastic deflector grill to which the motor is attached with a nut driver. Removed motor from grill and disconnected wire prongs (pull off). Attach new motor. Only issue - the ground prong has been moved to the front of the motor so the wire just reaches and has to be gently bent back so the fan blade clears it. Reattach deflector grill. Push on fan blade, but not too far to hit wire. Reassemble the rest in reverse order.

I was a Sears repair man for fourty eight years , so I don"t think I should say how easy this was.