1068265912 Kenmore Freezer - Instructions

I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.

Used a screwdriver to pry loose the old switch, swapped wires to the new switch and pushed it into the opening. Took about 2 minutes.

Great service. Unpluged old switch and pluged in new one. Works great

It was so easy I could have done the video. Many thank you's for saving me $79.00 in house call fees.... cindi

After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

Just as shown on a you tube video showing the steps involved, except I did not need to drill and tap the hole in the door. Cam repair kit contained all the correct parts.Freezer door is still working fine so I did not need to repair that door.

I'v used you 2 times for repairing my fridge and clothes dryer. . . . . So far you've saved me over a grand by doing it myself. . . Plus your service is nothing less than astounding. . . . . Both times I ordered early in the day and I got both orders the next day. . . . . You guys are sure on the ball. . . . . . Thanks

Removed the door, installed the lower cam & re-installed the door. Diagram & parts list correct. An easy repair.

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.

1. Used fine tip marker pen to draw outline of upper hinge position

2. unloaded food from door

3. took decorative cover off upper hing mount

4. loosened 3 screws (not completely) and lifted up upper hinge to permit upper door pin/hinge to come free.

5. lifted door off lower hinge.

6. remove broken pieces, cleaned, put in new pieces, added small amount of grease

7. put door on bottom hinge.

8. put top hinge into door

9. snugged up three screws in top hinge plate.

10. had to loosen top hinge screws and tap hinge plate around to get door to close by itself when about 1-2 inches from being closed

Best part was PartSelect save me bunches of money and got parts quickly

Empty the refrigerator door of all items and removable shleves.
Reomve top hinge (three screwsa at top of exterior).
Lift door off of bottom hinge pin.
Lay door across table
Remove top half of cam from door and replace with new cam half.
Remove bottom half of cam from bottom door hinge pin.
Lubricate both cam surfaces with small amount of silicone lubricant.
Replace door on bottom hinge pin and replace top hinge.
You may need help guiding teh door back onto the botttom hinge pin.
Replace all door shelves. Done!

I removed the door and replaced the door cams and reinstalled the door

I am a single female so the hardest part was lifting the door off and then trying to get it back on the hinge. I used the same bolts that were on the door so putting the new parts on was the easiest part. The slowest part was finding the right socket for the bolts and unscrewing the originals. Beats hiring a repair man.

removed door,removed worn part and replaced with new.