1068241581 Kenmore Freezer - Instructions

I watched the video on you tube and followed his instructions. It was very easy, it took about 20 minutes from start to finish.

Emptied the inside door. Took out the screws from the top hinge. Lifted the door off the bottom hinge. Laid the door on the kitchen table. Replaced the cam on the door. Replaced the cam on the bottom hinge. Placed door back on bottom hinge and put screws back on top.

This is a simple repair. the only reason it took as look as it did was because you need to empty the products from the door(s). Of course this is a good opportunity to thoroughly clean the fridge. The problem was caused by wear on the plastic spacer for the bottom hinge. Remove the plastic covers that conceal the top hinge located on top of the refrigerator. Remove the three bolts that attach the hinge to the housing. The door can then be lifted off the bottom hinge. Remove and replace the bottom spacer. Then remove and replace the receiver in the door by prying it out with a screwdriver or pliers and popping in the new one. I put a dab of lithium grease on the hinges before I reassembled them to reduce the wear and extend the life a little. Reverse the procedure to reassemble.

I have a KitchenAid side-by-side refrigerator and the right door clunked everytime it opened. We think it was damaged when contractors had to move the fridge and probably were too rough with it. I went on line and found that I could actually repair it myself (thanks to this web site, a great web site, by the way). I researched and found out through others that I needed a new door closing CAM kit. I only needed to fix 1 door, but bought the whole kit anyway (PS358690, Door Closing Cam Kit)to have spares. The kit showed up, I followed the great instructions via the video to remove the door, replaced the upper CAM on the door first and then ran into a snafu with the lower cam. The hinge on my model fridge does not have a replaceable CAM, it is physically attached to the door hinge. The instructions that came with the kit showed a hinge that was not my hinge - sigh. I had to put back all the old clunky parts, put the door back on and go order a new hinge (hopefully). Luckily there was a hinge available for my model with the CAM installed. I purchased it (PS331817, Door Hinge with Cam) and it came quickly like the other parts. I took the door off again (I knew how to do it this time), I replaced the hinge with ease, put the door back on and it is no CLUNK-FREE - Smooth like when we bought it. Thanks to everyone who wrote in about their clunking issues and thanks to PartSelect for the parts and the help.

Took out the door bins, 1 bolt on the plastic cap, 3 bolts on the hinge, took the door off, replaced cam at the bottom, all same size bolts, reset the door spent longer time cleaning the door selfs all done by my self in less than 30 min. others said it helped to have second pair of hands "my wife would of just got in the way :)"

Very easy!

Followed the awesome Youtube video posted by PartSelect! Gave me the confidence to do it, and I'm glad I did. Thanks everyone at PartSelect!

I followed the video instructions. Additionally the ordering process was easy and efficient and I received the parts promptly. Ordered on on 7/29/12 and received the parts on 7/31/12. The rep who took my order was very helpful and steered me to the right part. I'll use PartSelect again and will recommend them to my friends...ps. I have no connection whatsoever to this company.

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

I found this part on PartSelect. I was so excited it also showed a video on how to fix the door. My neighbor said he would help me and I ordered the pkg. It took 3 days to get here since I ordered Friday night and the part arrived Tuesday , this was the Easter Sunday week end also. Well the video said it was easy to do and I think it said it would take 15 min. My neighbor had it fixed in 10 min. I could not be happier. Thanks Part Select and my neighbor Mike.

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

Watched the video and viola, it was done. This was on the refrigerator side. Probably should have unplugged it, but didn't. One suggestion is hang a sheet in front to keep the cool in as best you can, even though it went really quickly.