1068253050 Kenmore Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Boca Raton, FL
- Parts Used:
- 4318165
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
refrig warm door cam broken
Follow instructions from owners manual. top hinge first then move door upward and replace broken cam with new parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clint from Idaho Falls, ID
- Parts Used:
- 4318165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Very Easy
Like most have stated this is a simple job. Nut-driver and six screws (on mine). Less than ten minutes. Like someone else said the hardest part was unloading the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Surprise, AZ
- Parts Used:
- WPW10329686
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The door would not stay shut.
We dealt with this problem for well over six months. Last week while visiting our home my mother tried to schedule a repair man to come out. Upon hearing this conversation i urged her to hang up the phone and let me fix it. This prompted me to go on line and find the three dollar part needed to fix it. With the help of a friend to lift and hold the door i unbolted the black closer piece and replaced it with the new one. This whole process took less than 10 minutes and completely fixed the problem. The service visit would have cost upwards of $80.00 so this was well worth the two days shipping i paid for.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jess from Manchester, TN
- Parts Used:
- WPW10329686
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Door not closing tightly
Removed the door, installed the lower cam & re-installed the door. Diagram & parts list correct. An easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Fountain Valley, CA
- Parts Used:
- WP944224
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken Kickplate Support Clip (Left side)
Unscrewed old broken part from the kickplate and attempted to install the new clip. Mounting screws would not go into the new clip. Had to drill out the mounting holes in the plastic clip using a #30 drill bit. Once the new clip was mounted, attempted to snap the kickplate back in place. Unfortunately at the left side the kickplate would not fully mate with the metal clip on the refrigerator body and would not snap all the way back to the refrigerator front surface, as the right side does. At least the kickplate doesn't fall down onto the floor on the left side as it did before. I suspect there is an alignment problem with the left side refrigerator metal clip, but have not pursued that yet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from spotsylvania, VA
- Parts Used:
- 4318165
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
refrigerator door would not stay closed
Just as shown on a you tube video showing the steps involved, except I did not need to drill and tap the hole in the door. Cam repair kit contained all the correct parts.Freezer door is still working fine so I did not need to repair that door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from CASTAIC, CA
- Parts Used:
- 4318165
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Replaced Cam For Closing Door.
I'v used you 2 times for repairing my fridge and clothes dryer. . . . . So far you've saved me over a grand by doing it myself. . . Plus your service is nothing less than astounding. . . . . Both times I ordered early in the day and I got both orders the next day. . . . . You guys are sure on the ball. . . . . . Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard H from Mason City, IA
- Parts Used:
- 4318165
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Teflon lower cam broke into from wear
removed door,removed worn part and replaced with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Prairieville, LA
- Parts Used:
- 4318165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Door would not swing shut on its own as normal.
Empty the refrigerator door of all items and removable shleves.
Reomve top hinge (three screwsa at top of exterior).
Lift door off of bottom hinge pin.
Lay door across table
Remove top half of cam from door and replace with new cam half.
Remove bottom half of cam from bottom door hinge pin.
Lubricate both cam surfaces with small amount of silicone lubricant.
Replace door on bottom hinge pin and replace top hinge.
You may need help guiding teh door back onto the botttom hinge pin.
Replace all door shelves. Done!
Reomve top hinge (three screwsa at top of exterior).
Lift door off of bottom hinge pin.
Lay door across table
Remove top half of cam from door and replace with new cam half.
Remove bottom half of cam from bottom door hinge pin.
Lubricate both cam surfaces with small amount of silicone lubricant.
Replace door on bottom hinge pin and replace top hinge.
You may need help guiding teh door back onto the botttom hinge pin.
Replace all door shelves. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Reading, PA
- Parts Used:
- 4318165
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set, Wrench set
Plastic door cams wore away over time
I removed the door and replaced the door cams and reinstalled the door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from Salt Lake City, UT
- Parts Used:
- 4318165
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
broken bottom door hinge, clunked when opened
I am a single female so the hardest part was lifting the door off and then trying to get it back on the hinge. I used the same bolts that were on the door so putting the new parts on was the easiest part. The slowest part was finding the right socket for the bolts and unscrewing the originals. Beats hiring a repair man.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Ft. Myers Beach, FL
- Parts Used:
- 4318165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench set
cams on lower hinge fractured and door wouln't close
1. Used fine tip marker pen to draw outline of upper hinge position
2. unloaded food from door
3. took decorative cover off upper hing mount
4. loosened 3 screws (not completely) and lifted up upper hinge to permit upper door pin/hinge to come free.
5. lifted door off lower hinge.
6. remove broken pieces, cleaned, put in new pieces, added small amount of grease
7. put door on bottom hinge.
8. put top hinge into door
9. snugged up three screws in top hinge plate.
10. had to loosen top hinge screws and tap hinge plate around to get door to close by itself when about 1-2 inches from being closed
Best part was PartSelect save me bunches of money and got parts quickly
2. unloaded food from door
3. took decorative cover off upper hing mount
4. loosened 3 screws (not completely) and lifted up upper hinge to permit upper door pin/hinge to come free.
5. lifted door off lower hinge.
6. remove broken pieces, cleaned, put in new pieces, added small amount of grease
7. put door on bottom hinge.
8. put top hinge into door
9. snugged up three screws in top hinge plate.
10. had to loosen top hinge screws and tap hinge plate around to get door to close by itself when about 1-2 inches from being closed
Best part was PartSelect save me bunches of money and got parts quickly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Phoenix, AZ
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb Replacement
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LOUIS from WOLCOTT, CT
- Parts Used:
- WPW10329686
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Knocking Noise When Opening@Closing Door
Removed door,took out old part@replaced with new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from ramona, CA
- Parts Used:
- 4318165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
refrig door was clunking when opening &closing.
rem upper hinge on door on & lifted door off. installed kit provided & ressemble.
Was this instruction helpful to you?
Thank you for voting!