1985816151 Kenmore Freezer - Instructions

Maytag made this easy. The water value was mounted to a plate on the back of the washer removed one screw, pulled the plate from the washer, removed the valve, reconnected the electrical connections and outlet hose, re inserted the plate, attached with screw and tested. 30 minutes tops and I hwve never done this before. Thanks to partsselect and others for recomenning the correct repair. Others had suggestjng the timer device ($180 +) for the parts. OUCH !!!!!

very simple to repair, three screws and disconnecting water supply pulling four wires then reverse steps and done, time spent less than 15 minutes.

My husband figured out what the problem was and I looked for the part. It was easy to find on your web-site, and the picture was spot on! I ordered it and had the part in 2 days. The repair took 15 minutes or less, and my washer is as good as new. Thank you PartSelect for being there when we needed. I will recommend this to everyone.

Just as the video described.... Unplugged the machine, turned off the water, both hot and cold. Unhooked the hoses (replaced them at this time since they were over 5 years old). Took out the top screw holding the frame piece and removed from machine. Took off the wires and the output hose. Removed the valve ass'y from the frame piece. Matched new to the original and reassembled in reverse order.

Very easy as the water inlet valve is located on the back of the washer and it was a simple matter of shutting off the water, undoing water hoses, undoing water inlet valve which didn't even need to remove the back side of the washer and connecting the new part, water hoses and turning water back on. The hardest part was tipping the washer, my sits on top of the cold air return, and balancing on a milk crate. Very pleased with being able to do my own repair.

Disconnected the electric plug and removed the water hoses from the washer. Took off the old water inlet valve under a plate on the washer and hooked in the new one. As we dismantled each section of the valve hook-up we connected that area of the new valve to be sure we got it connected correctly.

Shut water off and unplugged. Used channel locks to remove hoses. Used nut driver to remove mounting plate. Disconnected electrical connections to solenoids. Broke one. Had to replace. Used nut driver to loosen fill hose. Rusty and broke. Cut hose. Used new clamp to secure fill hose to fill solenoids. Stripped and crimped on new connector and replaced electrical connections as they were removed. Reinstalled hoses and plugged in. Tested A-OK.

The most important part of my repair was watching the video that was sent to me with my order confirmation. After I viewed it, the rest was easy. The only hard part was moving the washer away from the wall!

I ordered the part. Watched the video and did the repair. I removed the cover plate on the washer, removing the screws. I then, removed the broken water inlet valve and replaced it with the new one. I placed the cover plate back onto the rear of the washer and "VOILE", it was done. I am a divorced mother of three, who has never attempted to do any type of home repairs, however, the way PartSelect has set up the website, it made it easy to determine what part I needed and provided me with a video which gave me step by step instructions on how to repair it. I even posted my victory on Facebook! Thanks PartSelect.

Because the washer was old, 27 years, I actually ordered a new machine but after doing so was able to get the old washer to pump out the water. It had overfilled and spilled water on the floor. The next time I ran the washer using "warm" setting the hot water inlet solenoid failure was evident. I checked voltage at the solenoid and it was getting power so figured I'd try ordering a $30 part. In a couple of days it showed up and after less than :30 minutes I had the washer running again. It would have taken less time but a screw stripped out and I had to locate a replacement. I'd definitely recommend PartSelect. Oh, we cancelled the replacement washer and figured the Maytag repairman could resume his slumber!

Removed hoses and inlet valve from washer, replaced inlet valve by attaching the electrical connectors, reattached new water lines, returned inlet valve to its place in rear of washer. Checked for leaks, washed a load of clothes, everything worked properly.

very well . it was very easy 20 min.

First check that the screens are not plugged. There are fine screens in the mixing valve and at times you will find them in either end of the inlet hoses. Not a hard job if you can get to the back of the machine, just a few small screws, swap the wires to the new part and swap the outlet hose from the valve and screw it back together. Wife will think you are a wiz kid.

Unplugged AC cord. Removed hot and cold supply hoses. Removed front cover (2 Phillips screws near bottom). Raised lid, and removed fastening screw for injector tube. Removed retaining screws for inlet valve mounting plate. Positioned mounting plate partially inside rear of machine and removed (4) wires for solenoid connections. Re-positioned mounting plate slightly outside machine and removed valve mounting screws and old valve. Attached new valve (no modification to valve needed for my machine), and worked backwards through the steps listed above.

Be very, very careful not to cross thread the filler hose, onto the nylon valve housing. Recommend some lubrication, and a pair of velvet gloves.