GFU16F7AW3 Gibson Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joseph from Yulee, FL
- Parts Used:
- 5304518034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Coils not Defrosting and stopped freezing
Upluged power pulled freezer out from wall removed the two screws that holds the defrost timer unpluged defrost timer pluged new timer in mounted new timer back with the two screws pluged freezer back in and job was complete. Freezer working fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ronald from deering, NH
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
freezer would not freeze longer than one day. after ten years without problem
pulled out freezer, went to floor,reached in next to compressor pulled off clip just like on the video.Pulled off old capacitator took off wire leads.Installed new one. Freezer runs great.Loaded it up with beef pork and venison. No problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donn from Saint PAUL, MN
- Parts Used:
- 5303925377
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken shelf end cap
Truly a 10-second fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from Littleton, CO
- Parts Used:
- 5303925377
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The tabs on the shelf end broke off.
Removed the broken shelf ends and installed the new ones. Then installed the assembly on the freezer door. Trick was to put the long end of the tab in first followed by the short end. The up end was reversed on the opposite shelf end.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Macomb, MI
- Parts Used:
- 5304518034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Freezer was warm
I first noticed my ice cream getting soft. Then 2 days later the alarm went. I emptied the freezer, opened the panels and saw no frost. I saw that 99% of issues were resolved with a defrost timer and thermostat so I ordered those. I have to say the parts came quickly and they went in very easy. My freezer seems to be in the 1% category though. It's still not cooling even though I can measure the temperature at the front of the evaporator coil is cold but by the end of the coil it's almost room temperature. I think a repairman is called for.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Woodstock, GA
- Parts Used:
- 5304442620
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Fan in freezer quit
This was an easy job. First remove the ice maker, if you have one. Mine was mounted with just two screws. Loosen these screws, unplug the power cord at the connector and then lift the ice maker off. Remove the light bulb cover and the light bulb, just so you dont break it. Remove two hex screws and the back cover can be removed. My fan was mounted in the middle of a bracket retained between two rubber bushingings. Just push the fan blad of the shaft and pull the motoer out. Dissonect the power cord at the connector. My moter was differant than the replacement on the mounting so with the removial of the two screws on the motor I was able to exchange the upper and lower cast motoer housings. Reverse the assembly process and you good. Mine is running great.
Was this instruction helpful to you?
Thank you for voting!