GFU14F3AW1 Gibson Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Augusto from Gretna, LA
- Parts Used:
- 297216600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
thermostate stop working frozzen up
just like the video show sa 1,2,3 yeaaa thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven E from Lisle, IL
- Parts Used:
- 5304518034, 5304491584
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The defrost timer burned out.
This is an upright Frigidaire freezer. The defrost timer is at the bottom left side of the rear of the unit. One screw holds it in place and it only plugs in one way. When your freezer won't stay cold enough to freeze this is the first part to check. It is cheep to replace (20-30 dollars) and will usually fix the problem. It took about 5 minutes to replace the part and my freezer is up and running like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Port Republic, VA
- Parts Used:
- 297216600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer ran alot, then temperture began to vary.
Watched video on Part Select which shows you how to replace the thermostat with several good pointers. Very easily done and now the freezer works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edmond from Carroll, NH
- Parts Used:
- 297216600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer would not keep running and the temperature was too warm.
Followed the sites instructions. Empty the bottom part of the freezer. Remove the screws. Move the panel out of the way. Easily remove the old part and replace with the new. Put the panel and screws back in place. The freezer works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Winter Haven, FL
- Parts Used:
- 5304507201
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Gasket was worn and needed replaced. It was causing frost to form around inside of door.
Pulled the freezer out and unscrewed the screws around door. Gasket slide right out. After placing the new gasket, I used a hair dryer and sealed the gasket tighter. Works like a charm!! Very pleased with this do-it-yourself fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Yulee, FL
- Parts Used:
- 5304518034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Coils not Defrosting and stopped freezing
Upluged power pulled freezer out from wall removed the two screws that holds the defrost timer unpluged defrost timer pluged new timer in mounted new timer back with the two screws pluged freezer back in and job was complete. Freezer working fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laurin from Altamonte Springs, FL
- Parts Used:
- 5304507201
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Original freezer gasket worn out
Removed old gasket by backing out screws around inner door panel. I did not remove the screws just loosened in order to remove old gasket. Starting from the top of the inner door panel I set the old gasket and squared off. Tightened top screws and worked the gasket in on the sides and tightened several of the screws on the sides then set the bottom of gasket in the door. Inserting the gasket in the bottom was the hardest part of the job. The overall job took less time than expected.
Was this instruction helpful to you?
Thank you for voting!