86170-2 General Electric Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- william from san antonio, TX
- Parts Used:
- WB36X10003
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
bulb had broken off in base that was still screwed into socket
At first I tried to use pliers to unscrew the base,very uncomfortable working position,upside down and backwards(the microwave is installed over the range top)very limited space for your body and arms to manuver and you really cant see the base,all of this took place after the breaker was turned off ofcourse,finally figured out that you can drop the entire bottom housing of the microwave by unscrewing 6 screws and the light sockets are easily accessable once you lower it,take out 1 retaining screw ,remove the entire socket and unscrewed the broken base and replaced the bulbs,I said bulbs,there is no sense in having to replace another bulb in who knows how long since only one had burned out but they were both the same age
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from Semmes, AL
- Parts Used:
- 216008900
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Clicking sound then within a minute clicking again, not cooling.
UNPLUG REFRIGERATOR. Carefully remove relay from the side of the compressor. You shouldn't need a tool to do this, if it is hard you can gently pry the edge with a flat head screw driver just to loosen. Unplug white and red wires from relay, noting that the white wire goes in the hole with a #2 stamped beside it. Shake old relay, if it rattles like a baby rattler then it's most likely the problem. Replace wires into the new relay and plug back into the compressor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LUCY from BALLWIN, MO
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Changing the bulb that illuminates the cooktop
Loosen screw holding glass cover plate in place over bulb. Glass cover plate will swing down. Unscrew bad bulb, replace with good bulb, reset glass cover and tighten screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Jonestown, TX
- Parts Used:
- 216008900
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Stopped working, cooling.
I used a small screwdriver to disconnect wires from old starter. I connected the overload and starter, two wires. I put the unit back in the keeper, plugged the unit in, turned up the thermostat and it's working beautifully.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Neosho, MO
- Parts Used:
- 216008900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Freezer quit. Compressor would not start.
Like another post, the start relay rattled like a baby rattle. Replaced the start relay and freezer works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gilmar from Miami, FL
- Parts Used:
- 216008900
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
mottor starts than stop.
i looked byhind the freezer , the mottor has the relay connected to it.i took out the relay, and i descovery something was loose inside, i decided to take to check out at sears to see if they have in stock that especific relay. they did not have, they could order, that's when i dicided to go ahead and looking for in the internet, good i found PARTSELECT,they had the part and i was very nice attended,they sent in 2 days i had fix my freezer. thanks PARTSELECT. gilmar couto.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Cleveland, OH
- Parts Used:
- WB36X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
under microwave (above stove) light
The replacement of the light no problem, the reason the light broke; problem. The original was glued in (for transport i think) and simply trying to unscrew it out (in a very tight slot) it broke; be careful or you’ll be buying a new $20 bulb (with shipping and handling).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Fort Smith, AR
- Parts Used:
- WB36X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bulb burned ot
Un screwed the cover but when i tried to remove the bulb it was broken at the base. I disconnected the power and used neddle nosed pliers to remove the base
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from LISLE, IL
- Parts Used:
- 216502600
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
While defrosting freezer tossed the drain plug with ice and water into the sewer system.
Opened mailer and bag and place the drain plug into the drain. fit perfectly. In fact it is better than the one lost since the original needed a screwdriver or tool to remove the plug. This one has a flang or finger turner on it so that it can be removed. Also, does not interfere with items in bottom of freezer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Austin, TX
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Inside Bulb went out.
Remove top air grate via 2-screws. Remove metal top panel behind grate that's above bulb via 1-screw. Bulb is exposed and can be un-screwed. DONE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James H from KNOXVILLE, TN
- Parts Used:
- 3206256
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Ice crystals formed near gasket.
Removed the freezer door which had an electrical cord routed through the lower hinge with a disconnect under the freezer. Job works better with two people. Working the gasket into place was a little tricky at the corners. The putty knife was helpful. Make sure door is not warped when replaced on freezer. If warped slightly the door can be twisted to make gasket fit evenly bottom to top on front edge. Hope this helps DIY folks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Leesburg, FL
- Parts Used:
- WB36X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
NO light
.Thank You Dan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from UNIVERSITY PA, MD
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bulb burned out light that is under the microwave, which lights the oven below.
thank you for the video--very clear, responsible, applicable although the illustration was not exactly of our kind of light. the bulb was exactly like the one Hotpoint used in its microwave made in 1989! I will come back to you for parts in the future. (You have the model # from my original order.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from TREASURE IS, FL
- Parts Used:
- WB36X10003
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Under the microwave there are two light bulbs that light up the top of the oven/range.
Last week I removed the glass cover that was held in by one screw and removed the burnt out light bulb. I ordered the bulb and left the glass cover off until the bulb arrived. I had to wait until this evening to put the glass cover back on and fasten the screw because I have a window right next to the oven and the sun streaming in made it too difficult for me to see how to put the glass back in and replace the screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leon F. from Brookline, MA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Right hand surface lamp burned out. It apparently fald up and broke the glass cover. I wne on line when I found out the only local deaaler was some miles away and more expensive.
Simple. The parts came instantly. The glass was too big so I had it cut to size. I unscrewed the fixture with a screw driver replaced the bulb and slipped the glass cover into the frame and screwed the whole assembly in.
Was this instruction helpful to you?
Thank you for voting!