ZIF301NPPBII General Electric Freezer - Instructions

Unplugged the refrigerator first....then on the inside of the fridge, I popped the temp sensor cover off (upper LH side) and exposed the old sensor. I snipped off the old sensor about 3" down from the end and connected the new sensor (which I trimmed down to about 3" long) with some heat shrink wire nuts/connectors. Let the fridge run for a day or so and confirmed the problem was solved! Oh yeah, there was no way to tell the 2 wires apart (power vs. ground) on the sensor. However there was a manufacturer's stamp on the wires. So note the orientation of the text and mark one of the wires with a sharpie on both the old and new sensor before trimming. This will give you a reference for which wires to connect when adding the new sensor to the old wires.

took out shelves and removed the back plate my removing 2 screws with a nutdriver.removed the old defrost timer and defrost heater which was really easy.then installed the new ones.the video i watched on the website was really helpfull.

I decided to replace motor and fan, having previously altered/trimmed the fan which stopped the howling but caused a vibration. Unplug from mains. Clear out two top shelves in freezer. Remove light cover. Remove two screws(1/4 driver)at top of steel panel in rear of compartment and let it drop. Remove two screws above light. Pry up section above light/fan housing to access two screws retaining the light/fan assembly, loosen screws sufficiently so that assembly can be lifted and removed. Disconnect wiring plug by pinching in the sides of the plug and pulling out. Pull fan off motor shaft. Remove two screws clamping motor. Cut cable tie and molded wiring grommet to free wiring. The existing light wires can be removed from the old plug by carefully cutting around the old plug to free the pins and then pushing the pins into the new plug. Reverse procedure to assemble.

Followed the repair video, was spot on!!

luckly i have a bit of experience in refrigeration im an hvac technician by trade. this repair was a bit tricky in that i did not know at first if it was a Temperature Sensor issue or the main control board. I had tested the defrost termination thermostat and the defrost heater and as i suspected they were ok. Next i wanted to test the thermistors (temp sensors) it is hard to find technical data on these fridges. I needed to test the thermistors resistance @ a certian temperature to ensure they were working properly but where do u get such data? I also wanted to know some information about the logic programmed into the board (i.e when do you initiate defrost etc. . .). I had no such luck so i figured since i tested the defrost heater and thermostat and they were ok and all of the evap fans and such were working i'd order a circuit board and new thermistors. Got the CORRECT PARTS from this site in 2 business days and my fridge is working great! changing the parts was really easy, figuring out which parts to change was the only difficult thing about this job.

Condenser fan motor was running slow. This was not a problem included in your list of possible problems. I thought that maybe the capacitor was bad but have no way to check it. So I ordered one. when I received it, I installed it. That was not the problem. So I ordered a fan motor and installed it. That was not the problem. So finally I ordered a control board and installed it. That solved the problem. So maybe you should put "cond.fan motor runs slow" in your list of possible faults and what causes that problem. Capacitor was easy to install, simply remove the cover plate, flip off retaining wire, unplug the capacitor and replace. Fan motor was a bit more difficult. It must be removed from mount after fan scroll is removed. Remove one screw that holds scroll, bend the top down and remove. Then pull hard on fan blade to remove it. It must be installed on new motor. Two screws in frame mount can be removed with some effort if you have a 1/4" drive ratchet with a Phillips screwdriver bit. Then pull frame open and install new motor. Push fan blade on new motor shaft hard. Replacing control board was easy. I used a pair of long nose pliers with 90 degree bend to get mounting pins closed to pull board off.

followed part select video instructions

Ironically I did this today, as this email request came up asking how it went. I'm not a repairman, I'm a software engineer, and I can't thank this site enough for the step by step videos. With the video to help, this was a breeze, I was nervous as I had to empty all my freezer out onto the living room floor. Once that was done the repair took about 30 minutes. Thank you partselect!!!!! My second time doing business here, and I'll be coming back (well, if something breaks, so let's hope I don't have to).

Replaced all the sensors in both the feezer and refrigerator.Even though it colder now it still is not cold enough.Freezer won't freeze items but is cold and refrigerator still not real cold

remove the Ice tray, remove hex bolts from ice tray hangers on side of freezer. unscrew ice maker and remove it. Remove ice tray auger motor assembaly (4 hex bolts) remove 2 more hex bolts from top of rear inside panel. remove 4 hex bolts from lower panel as well. now with lower section out, you should see the last 2 hex bolts holding on plastic shield (top section rear panel) un screw light cover. Squeeze light fixture and push in. now remove entire top section of panel. All will be exposed. Remove old motor housing, disconnect wires, remove clip from coils. (NEW MOTOR DOES NOT HAVE CLIP OR WIRE FOR COILS)Attatch new motor and replace grommits. Reverse instructions for re installation.

followed you online video and it was easy and simple repair only took about an hour frig is back quiet and working fine thanks also parts come fast

i followed a video that was on your site, the video couldn't have been easier to follow it was step by step and very easy to follow, i replaced the evaporator fan motor and everything is working fine, i did notice that the evaporator coil was frozen pretty bad when i removed the back freezer panel i am going to check it again in a couple of weeks to make sure i don't have a defrosting problem as of now everything is fine i am hoping it was just the bad fan motor causing the coil to freeze up because of no air movement over the coil

My refrigerator was making a high pitched kind of howling noise. The PartSelect symptom that was closest was “unusual noise” and when I clicked that it said the evaporator fan motor fixes the symptom 32% of the time. Since my freezer fan speed sounded like it was constantly changing I went ahead and bought one which PartSelect delivered promptly. The installation video was great and although my freezer was not identical to the one in the video, the video was still very helpful. The only thing it didn’t say was how to tell if my freezer motor was the one with the thermistor although I suspect that they all are and that PartSelect is simply trying to save us money by showing us how to splice in a motor without a thermistor. Anyway, since I would have had to disassemble the freezer before buying the part to find out for sure, I just bought the one without the thermistor. This just meant I had to splice the new motor in, just like in the video. I think I would have preferred buying the motor with the thermistor even though it was more expensive. In the end my problem is solved so I’m happy. This is the third time that I’ve had to repair this GE refrigerator and PartSelect has been a valuable resource each time.

follow repair viedo

it was easy the only thing was i had to cut old harness to remove 2 wires that went to coil that had to go back in the new harness other then that a peice of cake.