FGVH2177TF0 Frigidaire Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Yvonne from CORP CHRISTI, TX
- Parts Used:
- 297309000, 5305878546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Fan motor died.
Remove shelves. Unplug unit. Unscrew back panel. Remove wire harness. Remove old fan. Insert new fan. Screw it in. Reattach wires harness. Plug unit in and make sure fan is on.
Reattach back panel. Put shelves back in.
Reattach back panel. Put shelves back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from RIVERSIDE, CA
- Parts Used:
- 5304511026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
door would not fully open
-got friend
-got step stool
-removed upper hing w/3/8 nut driver
-lifted door vertically off of lower hing pin (w/friend)
-removed and replaced broken nylon washer
-lifted door back onto lower pin hing hole
-while friend holds door reinstall upper hing bracket with 3/8 nut driver
-had cup of coffee
-got step stool
-removed upper hing w/3/8 nut driver
-lifted door vertically off of lower hing pin (w/friend)
-removed and replaced broken nylon washer
-lifted door back onto lower pin hing hole
-while friend holds door reinstall upper hing bracket with 3/8 nut driver
-had cup of coffee
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BETTY from SHINGLETOWN, CA
- Parts Used:
- 242015201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Scratch on stainless frig door.
Can't supply any info that would be helpful. Ordered a " badge" that covered 100% of the scratch and stuck it on. Scratch now covered and problem solved. Thanks for asking.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randolph from Edwards, MS
- Parts Used:
- 297309000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Evaporator fan not working
Took off cover, unplugged wires, removed old motor, mounted new motor, remounted new motor and replaced cover.
Now need a new control board for same model.
Now need a new control board for same model.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Toni from Little Rock, AR
- Parts Used:
- 297147700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Just lost key
No repair. The key fit!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- katrina from EAST ORANGE, NJ
- Parts Used:
- 297147700
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lost original key
Brought replacement key works just like original I thought it would be metal from reviews but it was plastic and still works perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelli from Goosecreek, SC
- Parts Used:
- 297147700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lost Key
It's easy to know how to use a key. I didn't have a difficult part, I didn't have the model # because I had lost my key and the model # is inside. I was able to find the energy saving paper that came with it but it had four model #'s. I called a couple places and no could me. I pulled up Part Select on line and just thought I would give them a try. I got a very nice person (Jeremy) He went thru every model that I had and three out of the four matched so he sent me a key and if it didn't work I could get my money back. I give him a A+ four taking that extra step, unlike the other places. Very satisfied!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from BRAINTREE, VT
- Parts Used:
- 218755405
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
A set scew was ordered twice.
The first order arrived in a huge box and there was no scew to be found, the box had wholes in it. I was given a refund and told to order again.
The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.
The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brenda from snellville, GA
- Parts Used:
- 297147700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Could Not Lock
Oh yea thanx to partselect it went great didnt get fisrtkey but when got the second key it worked great thanx partselect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nesbit from GOLDEN MEADOW, LA
- Parts Used:
- 242196204
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light doesn't work
i only ordered 1, so i replaced each 1 then moved to the next. still no light, so it must be someting else. will try to check the wires with a volt meter to see if i have power next. something wierd happen, when i accidently touch the back of the led board, it lit up, small but still light up. hoping that means the led board is goo, must be in the wiring. i saw it had a main led board so will check the power to that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from LEHIGH ACRES, FL
- Parts Used:
- 218755504
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
No problems
I had no problems. Screws arrived sooner than expected. It was a very simple installation. Very pleased with both the product and service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- hector from los fresnos, TX
- Parts Used:
- 297309000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
When I was ready to instal fan motor, I noticed that there was no thread where I was supposed to screw in the bolts
When i found out there was no thread in brace where bolts were supposed to screw in, I panicked. I thought I would have to send part back or go to a machine shop to make a thread. I called a friend for help and he told me the bolts would make the thread if I just screwed them in. Sure enough, the bolts made the thread and then I just proceeded to instal motor and put refrigerator back together. It was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Gilroy, CA
- Parts Used:
- 297309000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
condenser fan stop working
Replaced fan. I ordered the fan and received it the following.(-:
Was this instruction helpful to you?
Thank you for voting!
Evaporator Fan Motor Noise
The evaporator fan would make a very high-pitched whine/squealing noise usually after starting up after a defrost cycle, although, it would make the same noises during normal operation. After performing a thorough inspection of the fan blade and motor, I discovered that there was no interference to the rotating fan, and realized the motor must be failing. After removing the food and racks from the main body of the freezer, I had to remove 8 Philips-tipped screws that held the inside back panel cover on. I disconnected the fan motor from the main wiring harness, removed the fan mounting bracket (2 5/16" hex head screws), and then removed the fan motor from the mounting bracket (2 5/16" hex head bolts. I removed the fan blade and conducted a visual inspection, and found not blemishes of broken/damaged pieces. I mounted the new motor and used the existing fan blade, and replaced everything in the reverse order. I turned on the freezer and it has been operating perfectly since. I disassembled the old motor and discovered that the stator coils were worn, and the bearings allowed to much forward/aft motion.
Was this instruction helpful to you?
Thank you for voting!