FFFH20F2QWC Frigidaire Freezer - Instructions

My issue was water leaking from the door. I thought it was the gasket, so I removed the gasket and the entire panel off of the door. There was water behind it that had soaked the cardboard seal, so I left that front part off for over a week to let it dry. We determined between us and our two toddlers that perhaps the door hadn't been properly closed enough on a number of occasions, so before I bought a $100 gasket, I'd try making sure the door was shut with tape, turning the freezer on and seeing what happened. There was no water after a few days, so on another user's suggestion I purchased the $15 key and twist tied it to the freezer door. Now I am locking the door after use so we won't have leaking water any longer.

Replaced defrost thermostat and defrost timer on my commercial Kelvinator freezer. Took out screws inside freezer compartment that hold panel at top inside freezer.Once the screws were removed I pulled out the thermostat dial so the panel was free to drop down and expose coils to the freezer that were located in the top rear of the inside freezer compartment.The defrost thermostat was located on the top of the coil to the top left as you face the inside of the Kelvinator KFS220RHY1 freezer. Very easy unplug old and plug in new defrost thermostat. Also replaced timer located in the back side of the freezer down near the middle of the bottom of the freezer near the compressor. There were two nuts holding the timer in the back of the freezer once I took those out I just unplugged the old timer and plugged the new timer in ....very simple fix. I have only run my freezer for a week since I replaced both parts but so far all is working well.

thanks it worked out great we just needed extra self to create more compartments . this was a very easy and perfect fit for the model .

I knew from a problem years ago that the Thermostat was the likely cause so I ordered a new part and replaced it. Only need a phillips head screwdriver to remove the part and add the new one..

I removed the shelves, unscrewed the cover panel of the fan motor and regulator dial, disconnected the fan motor from power, unscrewed 2 screws holding the motor to the mounting bracket and put the new motor in it's place. New motor had no thread in the mounting holes, so I put new tread in so I could use the 2 screws. Another option would have been to drill all the way through the mounting holes and use longer screws or bolts. Of course I turned the power off before I started repairs. Freezer runs like new now. Technicians wanted $400 for the job, while it cost me a mere $55 for the Motor.

Removed the old defrost timer by removing 4 screws on the holding bracket. Disconnected the wire harness. Reconnected the wire harness to the new part. Installed the new part with 2 screws on the top of the molded bracket. I am a 67 year old woman... easy-peasy. (the defost timer is located in the bottom left rear of the freezer.

I order another one thanks

I removed the back cover and removed the clip holding the compressor- run capacitor and start relay. I replaced these 2 components and clean the dust from the frig., and from the bottom of the floor. I replaced the back cover ; Loss about $300 worth of meat when when the frig. failed. Then I thought that, during these turbulent times, there are many which don't have a refrigerator or any meat to place in it, The refrigerator is "running" normal again.

Removed items from door. Put down blanket on floor. Remove top hinge cover. Removed small bolts. Open and lift door off bottom hinge. Put on blanket on side and remover screw holding upper closure. Installed new closure. Removed bottom closure and installed new closure. Reinstalled door and closed to frame. Reinstalled top hinge and bolts adjusted door and tighten bolts. Reinstalled top hinge cover. For indicator light. Unplug unit and removed screws for kick plate. Removed light holder and removed terminals. Removed light and install in reverse order.

very simple,started by turning off the power to that outlet (in breaker panel) then removed the 3 bottom screws, 2 side screws and 3 top screws (all 8 screws are Phillips head) in order to remove the panel. Disconnected the motor (unplugged it) and removed the 2 screws holding the motor in place to remove the motor. I installed the Fan on the new motor, and remounted it in place , reconnected it and replaced the panel and all 8 screws. (and the side seals push back into place easily after you replace all the panel screws.
Very easy, it took less than 15 minutes to make repairs and freezer was back in operation and back to below freezing temps in less than an hour.

would take off working when the temp control was increase one number. Came here after I got to the number 7. Changed both parts the first time and temp control is working fine at 4. thanks for all the help

Turned freezer off and removed cover in freezer at the bottom, notice fan blades were broken off, removed the 2 screws that were holding the fan motor in place removed fan blade and replaced with new fan blade, problem solved

After removing the key from its shipping package I pushed it into the freezer locking slot and turned it to lock and unlock the lid and then removed it. I had no problems with this fix. Of course, I am an older gentleman with a lot of experience in repairs around my house,as well as other houses. I am sure that a less experienced person may have more of problem with this type of "repair".

I changed the cooling control

The timer in this older unit is clearly exposed at the back of the freezer underneath the freezer compartment. It is attached with two Phillips head screws. After the screws are removed, the timer can be unplugged and the new one plugged in. The new timer has an extra flange to allow it to be used on more than one model of freezer. In order to mount the timer in this unit, you have to remove the extra flange by carefully cutting it away from the timer body, in similar fashion to what's depicted in the online video. This will allow you to mount the new timer to the mounting plate using the two screws from the old timer.