43251-0B Frigidaire Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
old handle had shattered.
Removed pcs. of old handle, replaced new handle, installed handle trim strip. Took less than 5 min. Thanks
Was this instruction helpful to you?
Thank you for voting!
Broken handle on freezer
Could not be easier and I think it took me longer to open the packaging than it did to install. Remove the insert from the face of the old handle and remove the two screws (top & bottom) beneath the insert & discard broken handle (retain original screws). Put original screws through new handle, place in position and drive the screws in. Then snap in the insert panel. (My insert was old & brittle and did crack upon removal, but I had anticipated that and ordered a new insert as well.) Took 5 minutes....but I'm pretty handy and it might take someone else 6 minutes.
Was this instruction helpful to you?
Thank you for voting!
I bought the freezer used and it was missing the handle.
Ordered the replacement handle and insert. I replaced the handle in about 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mike from longview, TX
- Parts Used:
- 216446900
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
shut freezer-vacuum pump made hard to reopen-wife broke handle in tugging.
first removed two screws that held handle. Then replaced. Ordered a motor 3 years ago from land office with verbal over counter instructions and that was easier but to get part this time was very simple ! With the model number and name brand input on site I had part in 3 days instead of waiting for a chance to visit land store and HOPE they had the part. Y'all might consider a zoom feature for us older folks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Elmira, NY
- Parts Used:
- 216446900
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken handle
I was surprised that the screws and trim piece were not included so make sure you have them from the old handle or order new. First removed the broken ends still on the freezer. I removed the small metal brackets from the old handle and put them on the new one, screwed the handle to the freezer and put the trim piece on. Real easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martha M from Fort Worth, TX
- Parts Used:
- 216446900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The handle broke off the door
We removed the trim and the screws and kept them in a safe place until the handle arrived. It took only about 10 minutes start to finish. Very Easy!
Was this instruction helpful to you?
Thank you for voting!
Plastic shelf supports broken
Needed to remove both left and right broken (plastic) supports and reinsert the new parts. Not hard at all...worked like a charm!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Winlock, WA
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
won't start repaced the run capacitor didn't solve the problem so I ordered a defrost timer
I watched the videos (they really help) and followed the steps. Everything went smooth with no surprises
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jerry from petaluma, CA
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
refer quit cooling and so did freezer
I replaced the defrost timer,defrost thermostat,and run cap.as it turned out the compressor went bad. I dont know the model because but the time I got this review I replaced the refer with a knew one . two weeks living out of coolers was so much fun !!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Hudson, FL
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
not cold enough
per the video..easy installation....unfortunately the temperature did not improve. We still have a refrigerator temp in the upper freezer.....and a "cooler" in the refrigerator section
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANK from BRADENTON, FL
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Frige and freezer not cooling
I should have ordered start kit instead of start capacitor. The start cap astir did not fix problem so I ordered kit. Compasator comes as part of kit. Followed enclosed instructions. Cut existing wires and reconnected new wiring. Simple as that. It's a plug in item. Now worried it may be working to good. Freezer down to 10 deg. Watching to see if compressor is running to long. Seems ok lol. Wife hates me now. She wanted new frige.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- felder from logansport, LA
- Parts Used:
- 216446900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken door handle
backed out screws from old handle, install new hansel w/ same screws & screw cover. done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grace from Jackson, GA
- Parts Used:
- 216446900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door handle broke
Remove cover on handle, and unscrewed the old handle. Then reversed procedure
Was this instruction helpful to you?
Thank you for voting!
Had to replace door handle.
Nothing to it. Remove the center insert. Under there are two phillip head screws. Remove those, place new handle in position, apply screws, and put on the insert. Your done !
Was this instruction helpful to you?
Thank you for voting!
Our handle broke off
Our repair was very easy, just unscrew the old handle and replace it with the new one. The repair job took about two minutes and now the door is as good as new.
Was this instruction helpful to you?
Thank you for voting!