FFU14C3CW1 Frigidaire Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bill from Bay City, MI
- Parts Used:
- 5304464438
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Fridge quit working.
A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy installation, just in a tight space on my model.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- johan from redlands, CA
- Parts Used:
- 297311201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old Door Handle broke
Slipped off the top and bottom screw cover plates unscrewed the 4 retaining Phillips screws, removed the old handle and replaced it by reverse the procedure. The best part of the process was the amazing quick delivery and efficiency of Parts Select.
Was this instruction helpful to you?
Thank you for voting!
Plastic shelf supports broken
Needed to remove both left and right broken (plastic) supports and reinsert the new parts. Not hard at all...worked like a charm!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Salem, OR
- Parts Used:
- 297311201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken door handle
Even though we did not have the model or part number I was able to easily locate the exact part because of your photo, dimensions and video instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Calvin from New Port Richey, FL
- Parts Used:
- 297216004
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The frezzer ran continusly never shut off.
The installation was really simple, no problem. No instructions needed. What surprised me was, The new thermostat was installed in less then 24 hours after it was ordered. I live in FL
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ronald from deering, NH
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
freezer would not freeze longer than one day. after ten years without problem
pulled out freezer, went to floor,reached in next to compressor pulled off clip just like on the video.Pulled off old capacitator took off wire leads.Installed new one. Freezer runs great.Loaded it up with beef pork and venison. No problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wilson from indialantic, FL
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
compressor not running
thanks to all of the people who had the same problems I was able to make a quick fix on my fridge. I pulled the back cover off and found the compressor not kicking on so I replaced the start cap. and im back in bussiness.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from Palmyra, VA
- Parts Used:
- 297216004
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Initially on full time then off full time
A 1,2,3 approach: 1, order the right part at the best price, Part Select has easy to navigate website and provides updated info on what will work in your appliance at a fraction of other site costs. 2. Configure the appliance to control the temp for a few days to save the food. This is accomplished by jumpering the two control wires to keep the compressor on and plugging the appliance cord into a timer with a 2hr on and 4hr off cycle. use the thermometer verify 0 degrees. 3. When the temp control is delivered unplug the power cord and proceed to repace the temp control, using care not to crimp the temp sensor bulb tubing. A #1 phillips screwdriver will release the control housing and temp sensor clamp assy. When complete set control to mid range and plug appliance into wall outlet. Use thermometer to set desired temp.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Winter Haven, FL
- Parts Used:
- 5304507201
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Gasket was worn and needed replaced. It was causing frost to form around inside of door.
Pulled the freezer out and unscrewed the screws around door. Gasket slide right out. After placing the new gasket, I used a hair dryer and sealed the gasket tighter. Works like a charm!! Very pleased with this do-it-yourself fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jerry from petaluma, CA
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
refer quit cooling and so did freezer
I replaced the defrost timer,defrost thermostat,and run cap.as it turned out the compressor went bad. I dont know the model because but the time I got this review I replaced the refer with a knew one . two weeks living out of coolers was so much fun !!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bart from goldsboro, NC
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the compressor capacitor overheated
it was great. I ordered the capacitor for my frigidaire frig and it arrived
in 3 days. plugged in the part to the compressor and my frig has been
working ever since. I spent 3 minutes ordering the part and 30 seconds
attaching it to the frig. Easy, very easy. saved myself a 75 dollar repair
visit. thanks
in 3 days. plugged in the part to the compressor and my frig has been
working ever since. I spent 3 minutes ordering the part and 30 seconds
attaching it to the frig. Easy, very easy. saved myself a 75 dollar repair
visit. thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Hudson, FL
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
not cold enough
per the video..easy installation....unfortunately the temperature did not improve. We still have a refrigerator temp in the upper freezer.....and a "cooler" in the refrigerator section
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANK from BRADENTON, FL
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Frige and freezer not cooling
I should have ordered start kit instead of start capacitor. The start cap astir did not fix problem so I ordered kit. Compasator comes as part of kit. Followed enclosed instructions. Cut existing wires and reconnected new wiring. Simple as that. It's a plug in item. Now worried it may be working to good. Freezer down to 10 deg. Watching to see if compressor is running to long. Seems ok lol. Wife hates me now. She wanted new frige.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Winlock, WA
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
won't start repaced the run capacitor didn't solve the problem so I ordered a defrost timer
I watched the videos (they really help) and followed the steps. Everything went smooth with no surprises
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from Green River, WY
- Parts Used:
- 297311201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced broken door handle
Removed upper and lower screw covers. Removed 4 screws , Removed broken handle. Installed new handle with th 4 screws provided. Replaced screw covers. Done!
Was this instruction helpful to you?
Thank you for voting!