PLFH1779GS1 Frigidaire Freezer - Instructions

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .

Notice ice build up on the panel in front of the evaporator coil. Unplugged freezer and removed evaporator panel. Plugged unit back in and checked fan, coil "snap switch" and heater element, all seemed to check out good. Found defrost timer stuck in the freeze position, causing frost to accumulate over the evaporator. Manually rotated defrost timer to the 30min defrost cycle and system went into defrost. Ordered defrost timer and installed (part arrived in 3 days). Freezer works great again. Too bad I ended up throwing 400 dollars worth of meat away. the fix was very simple. Will definitely use PartSelect again. Thank you.

We were looking for a new freezer --thinking it wouldn't be worth calling a repairman. I was trying to determine the size of the freezer and couldn't find it in the manual. So I googled the model number and stumbled upon this site. Thought it would be worth a try and $12 plus shipping to replace the thermostat. Got the thermostat a couple days later, followed the video directions to replace it--not hard! Plugged it in and it is working great!!! SOOOOO glad I stumbled on your site! You saved us $700-$800!! Thank you! Thank you! Thank you!

removed screws with from the back panel of the freezer; located defrost thermostat attached to coil with a metal clip; unplugged thermostat and replaced with the new one. Put every thing back together and it works perfectly.

After testing and eliminating the temperature control and the timer as the problem, I turned to the thermostat. I had to wait for the ice buildup to thaw and then could remove the rear freezer panel (this was the 3rd time: first, to discover the ice buildup causing the problem, second when it came back after a complete thaw and test the thermostat, and this time to put the Partselect thermostat back in). My thermostat was visibly damaged from water melting into ice and expanding the casing and eventually breaking one of the connections. I connected the thermostat connection wires (not recommended) to get by while ordering the part, which shipped faster than local repair places could get it from their warehouses, and at a fraction of the cost. I'm really impressed with partselect's fast service and all the knowledgable customers who have explained how they installed them. I now have an intimate knowledge of how my fridge works and saved hundreds in repair, or twice that in replacement. Thanks!

I had to tap the screw holes with a 8/32 tap so that the screws would not bind.

Parts Select is an excellent source for help and parts identification. I highly recomend them.
My first option was to replace the defrost timer.
After still getting ice and frost buildup in freezer I decided to replace the defrost thermostat.
Remove all shelves. Losen icemaker if applicable. Remove light cover and bulb. Remove all screws securing rear vertical cover. Carefully move back panel, disconnect icemaker and bulb assembly. carefully remove styrofoam cover at upper left and remove defrost thermostat. I tested the thermostat and found it was defective. It would not close circuit after being placed in a working freezer. Reverse procedure to replace thermostat.
This solved the problem

I had no problems. Screws arrived sooner than expected. It was a very simple installation. Very pleased with both the product and service.

I unscrewed the screws that held the old fan on, disconnected the wiring harness and removed the old fan. I pulled the blades off the motor and put it on the new fan. One thing of note, the screw holes on the new fan weren't threaded. I assume this is by design, so I used the screws to thread the holes before installing it in the freezer. Once I did this, the rest of the installation was easy, just screw it back in and connect the wiring harness.

After researching other issues found on internet about same problem, decided to replace both thermostat and temperature control thermastat before going to the repairman way. I saw the videos given on this web site, ordered the parts and when they came in, unplugged freezer and started taking apart the back cover not sure what I would find. Turns out it was just that simple, unplugged the thermastat and unclipped it from the cooling fins, unplugged the temperature control switch and then plugged both units back in. The tricky part was coiling the temperature sensor ( not that tricky). I was done in about 45 minutes but that also included cleaning out and scrubbing the bottom and sides of freezer since I had everything out anyways. Started the freezer back up and took about 8 hours to freeze ice and other food at a setting of 4, where as before I had it set on 7 and was still not keeping the ice cream cold.

Remove the cover panel inside the freezer, remove and replace the fan motor (pull fan blades off old motor and push on the new one) and replace the cover.

Pulled freezer out from where located to allow shelves to be removed.Unplugged unit, removed shelves and evaporator cover, installed new fan motor. Plugged unit up to check fan motor operation. Reassembled unit, installed shelves and moved freezer back into original location.

TURN OFF WATER!! UNPLUG REFRIGERATOR!! Remove water fittings and electrical connector on old valve. Remove two mounting screws on pump bracket. Reverse procedure to install.

Upluged power pulled freezer out from wall removed the two screws that holds the defrost timer unpluged defrost timer pluged new timer in mounted new timer back with the two screws pluged freezer back in and job was complete. Freezer working fine.

I took 2 screws loose and undone water lines, replaced and reconnected everything. Real easy