TFFU2065FWA Frigidaire Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken door handle
Removed the trim pieces. Removed the handle screws and handle pieces. Install new handle using screws that were previously removed. Installed trim pieces.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from SLIDELL, LA
- Parts Used:
- 297216600
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
freezer would frost up and not get cold enough to keep frozen.
Removed shelves ,removed panel on interior back wall with Philips screwdriver ,unplugged wire terminals slid thermostat off coil ,then reversed process to complete installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tunis from NOLANVILLE, TX
- Parts Used:
- 297216600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer wouldn't shut off and wouldn't reach cold enough temperature.
Removed existing part, tested it, found it to be defective. OrderEd a new one and replaced the existing one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rex from BEDFORD, WY
- Parts Used:
- 5304513033
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Freezer would only run sometimes by turning the thermostat to highest position fully clockwise. Sometimes turning it full CW wouldn't turn on. Once the freezer would run on highest setting, it seemed that it wouldn't shut off. I put a thermometer inside and would read -15deg when running. +15-20deg.
Replaced thermostat and it fixed the problem. Freezer comes on and turns off automatically and regulates internal temperature around 2-5 degrees.
The hardest part was extending the coiled probe tubing and forming it to fit into clamp without kinking it.
The hardest part was extending the coiled probe tubing and forming it to fit into clamp without kinking it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Blaine from PIERRE, SD
- Parts Used:
- 5304513033, 297286803
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
freezer stops freezing, sounds and looks normal,, no compressor or fan sounds
would take off working when the temp control was increase one number. Came here after I got to the number 7. Changed both parts the first time and temp control is working fine at 4. thanks for all the help
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from ANDERSON, IN
- Parts Used:
- 5304513033, 297286803
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer would not run or get cold
Temp control thermostat fixed problem many thanks to Part Select for help with this problem.Was able to save majority of food.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVE from LOS RANCHOS, NM
- Parts Used:
- 5304518034
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Defrost Timer
The old defrost timer started making a screeching noise (probably bearings going out). The replacement part was a cinch to install. When I initially spoke to a PartsSelect person, they said the part number I gave them was not consistent with my old '94 Tappan Freezer. They were able to still find the proper replacement part number. The video that was on-line helpful also.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from CHAPPELL HILL, TX
- Parts Used:
- 5304507199
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Followed the instructions that were sent and repair was easy.
Followed the instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Jacksonville, FL
- Parts Used:
- 297217900, 5303305677
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Copper lines leaking freon
Removed the inside evaporator coil to do inside solder job, use torch to heat solder joints on the outside drier in order to remove it and install new drier. Soldered Heat exchanger line to drier and 1/4” copper line to compressor. Wrapped with new insulation wrap. Pulled a vacuum on system and then charged with 4.4 ounces of 134a freon. Works like a champ again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from DUNBAR, WV
- Parts Used:
- 297147700
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing key
After removing the key from its shipping package I pushed it into the freezer locking slot and turned it to lock and unlock the lid and then removed it. I had no problems with this fix. Of course, I am an older gentleman with a lot of experience in repairs around my house,as well as other houses. I am sure that a less experienced person may have more of problem with this type of "repair".
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marilyn from Dunlap, TN
- Parts Used:
- 5304513033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Freezer would not stop running and had frosted over
Pretty simple, take cover off back of freezer to access thermostat, unhook thermostat and replace with new one. It had wire hookups different from original part so had to look up that information. Turned out it did not matter which wire went on which prong.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from ROSTRAVER TWP, PA
- Parts Used:
- 5304513033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Freezer stopped cooling
Used Phillips head screw driver to remove panel to expose old thermostat control. Took picture with phone to use and a guide. Replaced old with new and placed panel back o . Working perfectly! 30 minute max to complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from PRAIRIEVILLE, LA
- Parts Used:
- 5304518034, 297216600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
No problems
It went exactly like your on line video. It took longer to defrost the freeze than it did to make the parts change out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mervin from BOYD, TX
- Parts Used:
- 5304513033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
It wouldn't restart when it turned off
I changed the cooling control
Was this instruction helpful to you?
Thank you for voting!