GLFH21F8HWA Frigidaire Freezer - Instructions

I followed the video. It’s not that it’s a bit difficult, it’s just going slowly and carefully.
The thing that I didn’t allow the 24 hours for the gasket to relax after leaving the box. Also, I forgot to heat the gasket and put a small layer of Vaseline.
So the next day I noticed the the gasket wasn’t seating properly and went back to the video and carefully followed the steps to gently heat it with a hair dryer and Vaseline. The gentle heat let the gasket properly relax and seat. The Vaseline helped created a small vacuum to complete the gaskets “training” to seal properly.
24 hours later it was beautiful and the freezer was working like new.
Parts Select was great to deal with.

I first replaced the defrost timer about a week prior and it did not correct the problem. I then ordered the thermostat from partselect and within 15 minutes had the part installed. My refridgerator has been running correctly for a couple weeks.

From discussions with friends, I determined the problem might be easy to fix. The fridge made a lot of noise, but the compressor DID come on, and inside the freezer was cold, but the main fridge was warming.

After unplugging the fridge, I removed the fan assembly in the freezer (there were about 4 nuts and a couple of plugs to uncouple.

I could see right away the fan blades has broken off, but the motor looked good. The new new fan pushed easily onto the shift and fit perfectly in the housing.

I reinstalled the fan assembly, plugged in the fridge, and right away heard the new fan come on - very quietly. What was a roar became a whisper and the fridge was down to 38 degrees with a few hours.

Best way is to watch the video on YouTube and follow the directions

The replacement of the Thermistor is a snap. Take out the bottom two shelves, remove the 8 screws in the back panel, pull it out. Cut the wires to the old thermistor and install the new one. There are demo's on you tube so I wont go into detail.

Unfortunately the replacement door seal was packaged with twists in it and would not lay flat on the door. I found the old seal was not the problem - but instead ice had grown between the door and the door panel so that the door would not seal properly. I reinstalled the old door seal and everything is fine now.

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

took door of removed gasket replaced

Needed a Phillips head screwdriver to remove bottom plate (kick panel). UNPLUGGED FREEZER. Removed plate pulled switch out through the mounting hole and unhooked the two electric wires. Placed wires on new switch, pushed wires back through the hole and seated the switch. Plugged in the freezer and opened the door - magic, the light came on. Replaced the front kick panel (hardest part was to line up the plate holes with the holes in the mounting bracket).

I removed the screws and replace the broken slide with the new slide. Put the basket drawer back on the track and it now stays in place and can easily be used once again.

Removed existing part, tested it, found it to be defective. OrderEd a new one and replaced the existing one.

Followed the instructions

Had to lossen around 60 screws to allow for the old gasket to be removed. Then I began the process of inserting the new gasket by fitting it into the gasket channel opened when I loosened the 60 screws. I inserted the gasket a little at a time making sure it was properly fitted then I tightened that part and then do the next part until I finished replacing the gasket.

Removed shelves ,removed panel on interior back wall with Philips screwdriver ,unplugged wire terminals slid thermostat off coil ,then reversed process to complete installation.

Removed the inside evaporator coil to do inside solder job, use torch to heat solder joints on the outside drier in order to remove it and install new drier. Soldered Heat exchanger line to drier and 1/4” copper line to compressor. Wrapped with new insulation wrap. Pulled a vacuum on system and then charged with 4.4 ounces of 134a freon. Works like a champ again!

I removed the plate (recommend using a magnetic phillips head screw driver to remmove screws which are recessed). I removed the old part and pushed the new part through the hole and carefully reached in behindto attach the wires to the new part.