FFU14F7HWL Frigidaire Freezer - Instructions

Removed the basket. Removed the two broken brackets (6 screws). Installed the two new brackets. Put the basket on the track. Done.

Used putty knife to pop out old control board. Which is located on the front of the freezer door. The hard part was determining that this was the problem in the first place. I first replaced the compressor controller and the Run Capacitor. compressor still would not start. when I installed the new control board, it ran perfect.

No repair. The key fit!

Unscrew all the fasteners from the door inner cover from the bottom to top to hold it in position, got rid of the old gasket.

I Cleaned all and install the new gastket into the door inner cover. then reintalled cover to the starting from the top to bottom to hold it in place.

this is a one man job but with two will be easer

Took off cover, unplugged wires, removed old motor, mounted new motor, remounted new motor and replaced cover.

Now need a new control board for same model.

It's easy to know how to use a key. I didn't have a difficult part, I didn't have the model # because I had lost my key and the model # is inside. I was able to find the energy saving paper that came with it but it had four model #'s. I called a couple places and no could me. I pulled up Part Select on line and just thought I would give them a try. I got a very nice person (Jeremy) He went thru every model that I had and three out of the four matched so he sent me a key and if it didn't work I could get my money back. I give him a A+ four taking that extra step, unlike the other places. Very satisfied!

Brought replacement key works just like original I thought it would be metal from reviews but it was plastic and still works perfectly

Oh yea thanx to partselect it went great didnt get fisrtkey but when got the second key it worked great thanx partselect

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .

When i found out there was no thread in brace where bolts were supposed to screw in, I panicked. I thought I would have to send part back or go to a machine shop to make a thread. I called a friend for help and he told me the bolts would make the thread if I just screwed them in. Sure enough, the bolts made the thread and then I just proceeded to instal motor and put refrigerator back together. It was simple.

Unplugged freezer from electrical socket. Removed lower trays from freezer. Removed sound proof stripping from sides of back panel. Removed upper, lower and side screws from back, lower panel using No. 2 phillips screwdriver. Disconnected motor wires from quick disconnect power supply. Removed motor bracket from freezer back using nut driver. Removed motor from bracket using same nut driver. Replaced motor and screws in bracket. reattached quick disconnect. Attached fan blade to motor making certain to push blade on shaft securely. Replaced bracket to freezer back. Replaced back cover. Replaced stripping. Plugged into power supply. Total time 15-20 minutes.

Pulled the freezer out and unscrewed the screws around door. Gasket slide right out. After placing the new gasket, I used a hair dryer and sealed the gasket tighter. Works like a charm!! Very pleased with this do-it-yourself fix.

I unscrewed the screws that held the old fan on, disconnected the wiring harness and removed the old fan. I pulled the blades off the motor and put it on the new fan. One thing of note, the screw holes on the new fan weren't threaded. I assume this is by design, so I used the screws to thread the holes before installing it in the freezer. Once I did this, the rest of the installation was easy, just screw it back in and connect the wiring harness.

Removed three screws each side to remove old slides. Needed spacers under new slide so that drawer would stay on track. Cut old slide to make spacers and installed both slides in 15 mins.

Remove the cover panel inside the freezer, remove and replace the fan motor (pull fan blades off old motor and push on the new one) and replace the cover.