GLFH1779GW0 Frigidaire Freezer - Instructions

Replaced fan. I ordered the fan and received it the following.(-:

Replace thermostat and show and tell made it easy.

Spent most of the time reading and understanding the instructions. The installation went ok. Relatively easy.

new house double wide came with refrigerate but no icemaker. The kit didnot come with water valve tap for water suply line that kit only cost 10$ at hareware store if i kown I needed it. I would have order it the same time. I did get everything in add on icemaker kit I forgot about water suply. very easy instull and my order came very fast thank you

My husband has never done this type of work and he found it very easy to read the instructions and follow the step by step process. Our only concern is that it should tell you before you begin that it takes 24 hours to produce ice, we thought we had a problem until we read further on into the instructions to find that out.

Followed the sites instructions. Empty the bottom part of the freezer. Remove the screws. Move the panel out of the way. Easily remove the old part and replace with the new. Put the panel and screws back in place. The freezer works.

Pulled freezer out from where located to allow shelves to be removed.Unplugged unit, removed shelves and evaporator cover, installed new fan motor. Plugged unit up to check fan motor operation. Reassembled unit, installed shelves and moved freezer back into original location.

Upluged power pulled freezer out from wall removed the two screws that holds the defrost timer unpluged defrost timer pluged new timer in mounted new timer back with the two screws pluged freezer back in and job was complete. Freezer working fine.

After researching other issues found on internet about same problem, decided to replace both thermostat and temperature control thermastat before going to the repairman way. I saw the videos given on this web site, ordered the parts and when they came in, unplugged freezer and started taking apart the back cover not sure what I would find. Turns out it was just that simple, unplugged the thermastat and unclipped it from the cooling fins, unplugged the temperature control switch and then plugged both units back in. The tricky part was coiling the temperature sensor ( not that tricky). I was done in about 45 minutes but that also included cleaning out and scrubbing the bottom and sides of freezer since I had everything out anyways. Started the freezer back up and took about 8 hours to freeze ice and other food at a setting of 4, where as before I had it set on 7 and was still not keeping the ice cream cold.

TURN OFF WATER!! UNPLUG REFRIGERATOR!! Remove water fittings and electrical connector on old valve. Remove two mounting screws on pump bracket. Reverse procedure to install.

Unplugged freezer from electrical socket. Removed lower trays from freezer. Removed sound proof stripping from sides of back panel. Removed upper, lower and side screws from back, lower panel using No. 2 phillips screwdriver. Disconnected motor wires from quick disconnect power supply. Removed motor bracket from freezer back using nut driver. Removed motor from bracket using same nut driver. Replaced motor and screws in bracket. reattached quick disconnect. Attached fan blade to motor making certain to push blade on shaft securely. Replaced bracket to freezer back. Replaced back cover. Replaced stripping. Plugged into power supply. Total time 15-20 minutes.

I took 2 screws loose and undone water lines, replaced and reconnected everything. Real easy

I noticed that the two gears weren't meshing together so upon inspection I saw that one of the gears had an inner piece missing making it weak so it kept popping out away from the other great. I ordered the new gear and unscrewed the old one off and put the new one on. So easy. It made Ice beautiful after that

i order the defrost timer and the temperaturecontrol as was advised,it was very simple as reading the previous notes, pulled knob off, rerout temp metal probe, while the cover was off i clean it as much as i could and repainted the bottom with applince paint, looks good as new, very easy, whent to the defrost timer was so simple unscreewbracket, pull wire clip harness replace harness rescreew bracket, replug freezer it's good as new, saved a lot of money, i love this web site

Remove back cover (5 screws )remove valve ( 1 screw ).Disconnect in and out water lines. Disconnect wire on solenoid. Install in reverse. Dont forget to turn off water.