PLFU2067DS1 Frigidaire Freezer - Instructions

The timer in this older unit is clearly exposed at the back of the freezer underneath the freezer compartment. It is attached with two Phillips head screws. After the screws are removed, the timer can be unplugged and the new one plugged in. The new timer has an extra flange to allow it to be used on more than one model of freezer. In order to mount the timer in this unit, you have to remove the extra flange by carefully cutting it away from the timer body, in similar fashion to what's depicted in the online video. This will allow you to mount the new timer to the mounting plate using the two screws from the old timer.

Pretty simple, take cover off back of freezer to access thermostat, unhook thermostat and replace with new one. It had wire hookups different from original part so had to look up that information. Turned out it did not matter which wire went on which prong.

Turned off water to inlet valve. Unbolted valve from back of unit, disconnect water supply line from valve, disconnected water line to ice maker. Put on new compression ring around water supply line. Pressed ice maker line into new valve, installed valve back on unit, then connected main supply line to valve. Works like a charm.

Removed power , unplugged wires and 2 screws then reversed the process 1 hour later first batch of cubes dropped into bin

The ice tray would fill up, but never spit the ice out. I pulled one screw out of the bottom of the ice maker and loosened the two on top. I dropped the unit, unpluged the power and reversed the previous steps to install the new ice maker. Completley easy.

First I determined the icemaker was the problem when it was no longer calling for water. You can hear that "whistle" for 6-7 seconds when it calls for water. Anyway, replacement was a piece of cake, but did not entirely fix my problem. I also had to flush the lines to the soloniods that allow water to flow through the filter and into the water storage tank because it was cloggged with a little piece of plastic.

After disassembling, the thermal fuse I ordered were not and exact fit, I had to cut off the ring terminals, strip the insulation back and splice it in.
It works.

Used Phillips head screw driver to remove panel to expose old thermostat control. Took picture with phone to use and a guide. Replaced old with new and placed panel back o . Working perfectly! 30 minute max to complete.

Ordered the Capacitor and the Thermostat Control. Parts were received in a matter of a few days, easy to install, but did not fix the problem. Had to call a repairman to fix the problem (compressor relay - this part not available to order for this model number with Parts Select). Will continue to use Parts Select in the future for other parts, but not happy that the actual part I needed was not available - had to use other methods.

It went exactly like your on line video. It took longer to defrost the freeze than it did to make the parts change out.

I changed the cooling control

removed the screws/nuts; pulled the back panel off, removed the old thermostat (wires just popped apart) replaced the new thermostat (wires just popped back on) replaced the back panel and the nuts and TaDa!!

First unplug freezer, then disconnected wires from timer.
Removed 2 screws from bracket holding time to freezer.
Attached New part with screws. .The mounting bracket is now part of New time. Reattach wires.
I let coils defrost and then plugged it.

watched the video (VERY helpful) and then removed the old icemaker and replaced it with the new one. Difficult only because of the small working space in the side by side freezer plus you can't see what you're doing when you tighten the screws. Working like a charm now.

Occasionally, we'd get one batch of ice cubes and a frozen lake of water in the bottom of the ice tray.

The installation was easy and I won't bother duplicating the comments of others who have installed this part.

One word of caution: The ice maker contains a heating element on the bottom. That element is apparently live even when the ice bar is in the upper (off) position. When I unscrewed the old ice maker and went to lift it off the bolts, I severely burned my finger on the bottom of the old ice maker because apparently I started the repair in the middle of the heating cycle.

I highly recommend that you unplug the ice maker entirely before doing the replacement and gingerly ensure that the unit isn't hot before touching it. You'll save yourself a nasty burn.