FFU14FC4CW3 Frigidaire Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Edmond from Carroll, NH
- Parts Used:
- 297216600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer would not keep running and the temperature was too warm.
Followed the sites instructions. Empty the bottom part of the freezer. Remove the screws. Move the panel out of the way. Easily remove the old part and replace with the new. Put the panel and screws back in place. The freezer works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Winter Haven, FL
- Parts Used:
- 5304507201
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Gasket was worn and needed replaced. It was causing frost to form around inside of door.
Pulled the freezer out and unscrewed the screws around door. Gasket slide right out. After placing the new gasket, I used a hair dryer and sealed the gasket tighter. Works like a charm!! Very pleased with this do-it-yourself fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Satellite Beach, FL
- Parts Used:
- 297309000
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fan would not start occasionally
I unscrewed the screws that held the old fan on, disconnected the wiring harness and removed the old fan. I pulled the blades off the motor and put it on the new fan. One thing of note, the screw holes on the new fan weren't threaded. I assume this is by design, so I used the screws to thread the holes before installing it in the freezer. Once I did this, the rest of the installation was easy, just screw it back in and connect the wiring harness.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CRAIG from PRESCOTT VALLEY, AZ
- Parts Used:
- 297309000
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Noisy fan
Remove the cover panel inside the freezer, remove and replace the fan motor (pull fan blades off old motor and push on the new one) and replace the cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Clovis, NM
- Parts Used:
- 297309000, 5308000010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Evaporator Fan Motor was making loud rattling sound.
Unplugged freezer from electrical socket. Removed lower trays from freezer. Removed sound proof stripping from sides of back panel. Removed upper, lower and side screws from back, lower panel using No. 2 phillips screwdriver. Disconnected motor wires from quick disconnect power supply. Removed motor bracket from freezer back using nut driver. Removed motor from bracket using same nut driver. Replaced motor and screws in bracket. reattached quick disconnect. Attached fan blade to motor making certain to push blade on shaft securely. Replaced bracket to freezer back. Replaced back cover. Replaced stripping. Plugged into power supply. Total time 15-20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Star Lake, NY
- Parts Used:
- 297147700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed a freezer key
We really didn t need to do a repair, we just ordered a freezer key that we didn t have. I must say the shipping was fast we received it the next day. It was worth the shipping charge. We will be ordering again. Great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Fresno, CA
- Parts Used:
- 297147700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
freezer door got locked and we couldn't find the key
inserted key and turned
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Augusto from Gretna, LA
- Parts Used:
- 297216600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
thermostate stop working frozzen up
just like the video show sa 1,2,3 yeaaa thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from royal oaks, CA
- Parts Used:
- 5304518034, 297216600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
coils would freeze over not allowing air to circulate throughout freezer
replace thermostat and timer after defrosting and cleaning out freezer. I took less than 10 minutes and now freezer has a defrost cycle that eliminates frost buildup on the coils.
Was this instruction helpful to you?
Thank you for voting!