AFFU2066DW0 Frigidaire Freezer - Instructions

replaced controller start capacitor as per troubleshooting checklist. Was not the problem, then replace controller kit. seems to have resolved the problem.Temperature more constant. The problem with this refrig though in my opinion is that only one thermostat controls both the freezer compartment evap fan in freezercompartment also blows cold air into refrigcomp. There is not very much control over both temps. Am in monitoring both compartments and hoping that freezer will keep things frozen

Replaced fan. I ordered the fan and received it the following.(-:

per the video..easy installation....unfortunately the temperature did not improve. We still have a refrigerator temp in the upper freezer.....and a "cooler" in the refrigerator section

I ordered a new thermostat and installed it in less than 15 minutes. Looks like the problem is fixed. Now ,the freezer cycles on and off correctly. The part was ordered on a Monday and I got it the next day. I am very satisfied.

I should have ordered start kit instead of start capacitor. The start cap astir did not fix problem so I ordered kit. Compasator comes as part of kit. Followed enclosed instructions. Cut existing wires and reconnected new wiring. Simple as that. It's a plug in item. Now worried it may be working to good. Freezer down to 10 deg. Watching to see if compressor is running to long. Seems ok lol. Wife hates me now. She wanted new frige.

Watched video on Part Select which shows you how to replace the thermostat with several good pointers. Very easily done and now the freezer works great.

i order the defrost timer and the temperaturecontrol as was advised,it was very simple as reading the previous notes, pulled knob off, rerout temp metal probe, while the cover was off i clean it as much as i could and repainted the bottom with applince paint, looks good as new, very easy, whent to the defrost timer was so simple unscreewbracket, pull wire clip harness replace harness rescreew bracket, replug freezer it's good as new, saved a lot of money, i love this web site

When i found out there was no thread in brace where bolts were supposed to screw in, I panicked. I thought I would have to send part back or go to a machine shop to make a thread. I called a friend for help and he told me the bolts would make the thread if I just screwed them in. Sure enough, the bolts made the thread and then I just proceeded to instal motor and put refrigerator back together. It was simple.

Unplugged freezer from electrical socket. Removed lower trays from freezer. Removed sound proof stripping from sides of back panel. Removed upper, lower and side screws from back, lower panel using No. 2 phillips screwdriver. Disconnected motor wires from quick disconnect power supply. Removed motor bracket from freezer back using nut driver. Removed motor from bracket using same nut driver. Replaced motor and screws in bracket. reattached quick disconnect. Attached fan blade to motor making certain to push blade on shaft securely. Replaced bracket to freezer back. Replaced back cover. Replaced stripping. Plugged into power supply. Total time 15-20 minutes.

We really didn t need to do a repair, we just ordered a freezer key that we didn t have. I must say the shipping was fast we received it the next day. It was worth the shipping charge. We will be ordering again. Great service.

Plugged in the new parts. No tools were required. Sears wanted to charge me $300 for the repair!

Not sure if it was the Controller or the run capacitor that went bad and took out the controller, so, purchased both an replaced both. Snapped of the wire retainer,unpluged the controller, used pliers and small screw driver to disconnect the controller, plugged wires into the new controller, plug the run capacitor into it ahd reinstalled, so far running great.

inserted key and turned

The evaporator fan would make a very high-pitched whine/squealing noise usually after starting up after a defrost cycle, although, it would make the same noises during normal operation. After performing a thorough inspection of the fan blade and motor, I discovered that there was no interference to the rotating fan, and realized the motor must be failing. After removing the food and racks from the main body of the freezer, I had to remove 8 Philips-tipped screws that held the inside back panel cover on. I disconnected the fan motor from the main wiring harness, removed the fan mounting bracket (2 5/16" hex head screws), and then removed the fan motor from the mounting bracket (2 5/16" hex head bolts. I removed the fan blade and conducted a visual inspection, and found not blemishes of broken/damaged pieces. I mounted the new motor and used the existing fan blade, and replaced everything in the reverse order. I turned on the freezer and it has been operating perfectly since. I disassembled the old motor and discovered that the stator coils were worn, and the bearings allowed to much forward/aft motion.

pulled out freezer, went to floor,reached in next to compressor pulled off clip just like on the video.Pulled off old capacitator took off wire leads.Installed new one. Freezer runs great.Loaded it up with beef pork and venison. No problems.