FFU21C4CW6 Frigidaire Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Paulden, AZ
- Parts Used:
- 297036907
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replace air filter light was on not on know
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrea from MANLIUS, NY
- Parts Used:
- 297311201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Oven not reaching temperature
Using the socket wrench, I removed the old element from the oven wall attached by two hexagonal screws. I then removed the electrical attachment to the oven using a Philips head screw driver. Replaced the element with the new one and reversed the process. The oven works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from HARDING, PA
- Parts Used:
- 297216004
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer wouldn’t turn on.
Put the new temperature control unit in plugged freezer back in and immediately turned on. Very simple repair. Saved a lot of money not having to purchase new or call a repair shop.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelli from Goosecreek, SC
- Parts Used:
- 297147700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lost Key
It's easy to know how to use a key. I didn't have a difficult part, I didn't have the model # because I had lost my key and the model # is inside. I was able to find the energy saving paper that came with it but it had four model #'s. I called a couple places and no could me. I pulled up Part Select on line and just thought I would give them a try. I got a very nice person (Jeremy) He went thru every model that I had and three out of the four matched so he sent me a key and if it didn't work I could get my money back. I give him a A+ four taking that extra step, unlike the other places. Very satisfied!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- katrina from EAST ORANGE, NJ
- Parts Used:
- 297147700
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lost original key
Brought replacement key works just like original I thought it would be metal from reviews but it was plastic and still works perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brenda from snellville, GA
- Parts Used:
- 297147700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Could Not Lock
Oh yea thanx to partselect it went great didnt get fisrtkey but when got the second key it worked great thanx partselect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- johan from redlands, CA
- Parts Used:
- 297311201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old Door Handle broke
Slipped off the top and bottom screw cover plates unscrewed the 4 retaining Phillips screws, removed the old handle and replaced it by reverse the procedure. The best part of the process was the amazing quick delivery and efficiency of Parts Select.
Was this instruction helpful to you?
Thank you for voting!
Plastic shelf supports broken
Needed to remove both left and right broken (plastic) supports and reinsert the new parts. Not hard at all...worked like a charm!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Newhebron, MS
- Parts Used:
- 5304464438, 5304491585
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Freezer wasn't keeping things frozen
Plugged in the new parts. No tools were required. Sears wanted to charge me $300 for the repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Model, CO
- Parts Used:
- 5304464438, 5304491585
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Freezer not freezing
Not sure if it was the Controller or the run capacitor that went bad and took out the controller, so, purchased both an replaced both. Snapped of the wire retainer,unpluged the controller, used pliers and small screw driver to disconnect the controller, plugged wires into the new controller, plug the run capacitor into it ahd reinstalled, so far running great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Hudson, FL
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
not cold enough
per the video..easy installation....unfortunately the temperature did not improve. We still have a refrigerator temp in the upper freezer.....and a "cooler" in the refrigerator section
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANK from BRADENTON, FL
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Frige and freezer not cooling
I should have ordered start kit instead of start capacitor. The start cap astir did not fix problem so I ordered kit. Compasator comes as part of kit. Followed enclosed instructions. Cut existing wires and reconnected new wiring. Simple as that. It's a plug in item. Now worried it may be working to good. Freezer down to 10 deg. Watching to see if compressor is running to long. Seems ok lol. Wife hates me now. She wanted new frige.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Parlin, NJ
- Parts Used:
- 5304491585
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
freezer not maintining adequate temperature
replaced controller start capacitor as per troubleshooting checklist. Was not the problem, then replace controller kit. seems to have resolved the problem.Temperature more constant. The problem with this refrig though in my opinion is that only one thermostat controls both the freezer compartment evap fan in freezercompartment also blows cold air into refrigcomp. There is not very much control over both temps. Am in monitoring both compartments and hoping that freezer will keep things frozen
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from Palmyra, VA
- Parts Used:
- 297216004
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Initially on full time then off full time
A 1,2,3 approach: 1, order the right part at the best price, Part Select has easy to navigate website and provides updated info on what will work in your appliance at a fraction of other site costs. 2. Configure the appliance to control the temp for a few days to save the food. This is accomplished by jumpering the two control wires to keep the compressor on and plugging the appliance cord into a timer with a 2hr on and 4hr off cycle. use the thermometer verify 0 degrees. 3. When the temp control is delivered unplug the power cord and proceed to repace the temp control, using care not to crimp the temp sensor bulb tubing. A #1 phillips screwdriver will release the control housing and temp sensor clamp assy. When complete set control to mid range and plug appliance into wall outlet. Use thermometer to set desired temp.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Winlock, WA
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
won't start repaced the run capacitor didn't solve the problem so I ordered a defrost timer
I watched the videos (they really help) and followed the steps. Everything went smooth with no surprises
Was this instruction helpful to you?
Thank you for voting!