MFU14F3GW0 Frigidaire Freezer - Instructions

Brought replacement key works just like original I thought it would be metal from reviews but it was plastic and still works perfectly

Oh yea thanx to partselect it went great didnt get fisrtkey but when got the second key it worked great thanx partselect

Notice ice build up on the panel in front of the evaporator coil. Unplugged freezer and removed evaporator panel. Plugged unit back in and checked fan, coil "snap switch" and heater element, all seemed to check out good. Found defrost timer stuck in the freeze position, causing frost to accumulate over the evaporator. Manually rotated defrost timer to the 30min defrost cycle and system went into defrost. Ordered defrost timer and installed (part arrived in 3 days). Freezer works great again. Too bad I ended up throwing 400 dollars worth of meat away. the fix was very simple. Will definitely use PartSelect again. Thank you.

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .

Pulled the freezer out and unscrewed the screws around door. Gasket slide right out. After placing the new gasket, I used a hair dryer and sealed the gasket tighter. Works like a charm!! Very pleased with this do-it-yourself fix.

Upluged power pulled freezer out from wall removed the two screws that holds the defrost timer unpluged defrost timer pluged new timer in mounted new timer back with the two screws pluged freezer back in and job was complete. Freezer working fine.

Ordered freezer key friday afternoon received it saturday afternoon. Fast service

The sliding shelf side rail is held by three philips head screws that tighten into nut inserts. No amount of tightening would keep two of the three screws tight. I found that the nut inserts which are plastic and insert into the side of the freezer would pull loose, probably from years of overloading the sliding shelf basket. Ordered two nut inserts from PartSelect. 1. Remove three screws to remove shelf slide side rail. 2. Remove nut inserts to be replaced with needle nose pliers or reinsert screw a couple of turns and pull nut insert out with pliers. 3. Insert new nut inserts, position side rail, and tighten screws. Replace sliding shelf/basket.

I first noticed my ice cream getting soft. Then 2 days later the alarm went. I emptied the freezer, opened the panels and saw no frost. I saw that 99% of issues were resolved with a defrost timer and thermostat so I ordered those. I have to say the parts came quickly and they went in very easy. My freezer seems to be in the 1% category though. It's still not cooling even though I can measure the temperature at the front of the evaporator coil is cold but by the end of the coil it's almost room temperature. I think a repairman is called for.

Removed old gasket by backing out screws around inner door panel. I did not remove the screws just loosened in order to remove old gasket. Starting from the top of the inner door panel I set the old gasket and squared off. Tightened top screws and worked the gasket in on the sides and tightened several of the screws on the sides then set the bottom of gasket in the door. Inserting the gasket in the bottom was the hardest part of the job. The overall job took less time than expected.

Took interior panel off and uncliped yhe termination switch and cliped the new one on the coil and connected the two wires very simple. The defrost timer was located in the rear of the unit on the right side at the bottom. Removed the 2 screws holding the bracket unpluged the timer and removed the timer. The new timer allready had a bracket so just plug in and install the 2 screws. Pluged the unit in and worked great make sure that the freezer is unpluged before changing any part

We really didn t need to do a repair, we just ordered a freezer key that we didn t have. I must say the shipping was fast we received it the next day. It was worth the shipping charge. We will be ordering again. Great service.

inserted key and turned

This was an easy job. First remove the ice maker, if you have one. Mine was mounted with just two screws. Loosen these screws, unplug the power cord at the connector and then lift the ice maker off. Remove the light bulb cover and the light bulb, just so you dont break it. Remove two hex screws and the back cover can be removed. My fan was mounted in the middle of a bracket retained between two rubber bushingings. Just push the fan blad of the shaft and pull the motoer out. Dissonect the power cord at the connector. My moter was differant than the replacement on the mounting so with the removial of the two screws on the motor I was able to exchange the upper and lower cast motoer housings. Reverse the assembly process and you good. Mine is running great.