FFU20FC4AW2 Frigidaire Freezer - Instructions

First unplug freezer, then disconnected wires from timer.
Removed 2 screws from bracket holding time to freezer.
Attached New part with screws. .The mounting bracket is now part of New time. Reattach wires.
I let coils defrost and then plugged it.

Ordered the replacement handle and insert. I replaced the handle in about 10 minutes.

Purchased gasket from parts plus installed it and door still won’t stay shut without duct tape plus the frost is building up really bad looking for another parts store to get problem fixed

Could not be easier and I think it took me longer to open the packaging than it did to install. Remove the insert from the face of the old handle and remove the two screws (top & bottom) beneath the insert & discard broken handle (retain original screws). Put original screws through new handle, place in position and drive the screws in. Then snap in the insert panel. (My insert was old & brittle and did crack upon removal, but I had anticipated that and ordered a new insert as well.) Took 5 minutes....but I'm pretty handy and it might take someone else 6 minutes.

1. Ensure that the power is completely removed from the freezer. 2. Using needle-nose pliers and a screw driver, remove the wire retainer holding the controller assembly to the compressor and remove the controller assembly by pulling away from the compressor. 3. Cut the two wires from the existing controller assembly and strip the ends about a quarter of an inch. 4. Slide the heat shrink tubing over the wires of the connector provided with the controller kit. 5. Use the Blue Barrel connectors provided with the controller kit to connect the controller wires provided in the kit to the existing wires of the freezer. **Ensure that they are well crimped. 6. Using a heat gun, shrink the tubing to fit over the connector and wires. **Be careful not to overheat. 7. Plug the connector into the new controller provided in the kit. 8. Plug the controller assembly back into the socket on the compressor. 9. Reattach the wire retainer securely to hold the controller assembly to the compressor. 10. Plug in the freezer and adjust the thermostat so that the compressor energizes. If the controller was the issue your freezer should begin to cool.

freezer section remove ice trays ,shelves,unplug ice tray.use 1/4 nut driver remove back panel,use hair dryer thaw ice from evap coil ,unplug tstat remove install new one.plug in ice maker,put back panel back on ,ice maker and shelves plug refridgerator back in

Removed pcs. of old handle, replaced new handle, installed handle trim strip. Took less than 5 min. Thanks

The old defrost timer started making a screeching noise (probably bearings going out). The replacement part was a cinch to install. When I initially spoke to a PartsSelect person, they said the part number I gave them was not consistent with my old '94 Tappan Freezer. They were able to still find the proper replacement part number. The video that was on-line helpful also.

Bought the defrost timer based on PartSelect recommendations, installed it and no change. Apparently the old one was fine but since the refrigerator was in a flood and this part got submerged in water I kept it rather than returning it. I looked at everything closely and realized all the mechanical functions were working properly. Rarely does a condenser coil fail so I decided to look into recharging the coolant. Bought a 1/4 inch bullet valve, a 12oz. can of R-134a and a cheap resealable can adapter with hose, gauge and R22 to R-134a adapters. After a $30. investment Bingo, after one squirt the refrigerator began to cool and after 4oz. it now works better than new. I understand that PartSelect is in the business of selling only their parts but please consider that there can be other simple problems.

No repair. The key fit!

By simply popping off the handle cover the two screws were revealed which attach the handle to the door. New handle fit exactly like the old one. Easy peezzy lemon squeezy.

first removed two screws that held handle. Then replaced. Ordered a motor 3 years ago from land office with verbal over counter instructions and that was easier but to get part this time was very simple ! With the model number and name brand input on site I had part in 3 days instead of waiting for a chance to visit land store and HOPE they had the part. Y'all might consider a zoom feature for us older folks.

I was surprised that the screws and trim piece were not included so make sure you have them from the old handle or order new. First removed the broken ends still on the freezer. I removed the small metal brackets from the old handle and put them on the new one, screwed the handle to the freezer and put the trim piece on. Real easy.

It's easy to know how to use a key. I didn't have a difficult part, I didn't have the model # because I had lost my key and the model # is inside. I was able to find the energy saving paper that came with it but it had four model #'s. I called a couple places and no could me. I pulled up Part Select on line and just thought I would give them a try. I got a very nice person (Jeremy) He went thru every model that I had and three out of the four matched so he sent me a key and if it didn't work I could get my money back. I give him a A+ four taking that extra step, unlike the other places. Very satisfied!

I used the tool at Partselect that in theory allows diagnostic of the problem to be repaired. The result was that more tan 90% of the time with the introduced symptoms it had to be the thermostat. I order the part, got it quickly and installed. It did not fix the problem. So, be careful with the diagnostic tool, because it is just based on what most people buy when they have a particular problem. Videos for installation are great. If diagnosis was better, this would be fantastic. In my case there might be a different problem.