FFU17FC4AW3 Frigidaire Freezer - Instructions

I used the tool at Partselect that in theory allows diagnostic of the problem to be repaired. The result was that more tan 90% of the time with the introduced symptoms it had to be the thermostat. I order the part, got it quickly and installed. It did not fix the problem. So, be careful with the diagnostic tool, because it is just based on what most people buy when they have a particular problem. Videos for installation are great. If diagnosis was better, this would be fantastic. In my case there might be a different problem.

Had to remove all screws on rear back cover of freezer inside, unplugged refridgerator, uncliped thermostat, unpluged thermostat. Replaced thermostat with new one in the same location, and let defrost fulley. Reassembled, pluged in, and tested. All was good. But I did also replace timer at first part of the repair so I suggest you replace both at the same time.

Removed the back panel in freezer compartment with the nut-driver. Then I cut off old thermostat connections, and spliced in new thermostat connections (repairman had already replaced defrost timer, and said not to trust connectors included on wires-they failed often). Then I snapped thermostat itself onto cooler coil. So far so good, fridge is running at 35-40 degrees a week later. Thanks Parts-Select!!!

Ordered the replacement handle and insert. I replaced the handle in about 10 minutes.

Could not be easier and I think it took me longer to open the packaging than it did to install. Remove the insert from the face of the old handle and remove the two screws (top & bottom) beneath the insert & discard broken handle (retain original screws). Put original screws through new handle, place in position and drive the screws in. Then snap in the insert panel. (My insert was old & brittle and did crack upon removal, but I had anticipated that and ordered a new insert as well.) Took 5 minutes....but I'm pretty handy and it might take someone else 6 minutes.

Removed pcs. of old handle, replaced new handle, installed handle trim strip. Took less than 5 min. Thanks

A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy installation, just in a tight space on my model.

freezer section remove ice trays ,shelves,unplug ice tray.use 1/4 nut driver remove back panel,use hair dryer thaw ice from evap coil ,unplug tstat remove install new one.plug in ice maker,put back panel back on ,ice maker and shelves plug refridgerator back in

We are not handy, we had an appliance repair person install the gasket.

Loosened the screws all around the door. easier if you take the door off the unit and lay it on a table. Cover the table with a blanket to protect the door finish. Old gasket just pulls loose. Press the raised bead on the new gasket under the plastic strip. Corners were the most difficult. Retighten the the screws and rehang the door. It took some practice to get the bead under the plastic strip.

By simply popping off the handle cover the two screws were revealed which attach the handle to the door. New handle fit exactly like the old one. Easy peezzy lemon squeezy.

No repair. The key fit!

I was surprised that the screws and trim piece were not included so make sure you have them from the old handle or order new. First removed the broken ends still on the freezer. I removed the small metal brackets from the old handle and put them on the new one, screwed the handle to the freezer and put the trim piece on. Real easy.

Brought replacement key works just like original I thought it would be metal from reviews but it was plastic and still works perfectly

first removed two screws that held handle. Then replaced. Ordered a motor 3 years ago from land office with verbal over counter instructions and that was easier but to get part this time was very simple ! With the model number and name brand input on site I had part in 3 days instead of waiting for a chance to visit land store and HOPE they had the part. Y'all might consider a zoom feature for us older folks.