FFU20FC6AW5 Frigidaire Freezer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Camarillo, CA
- Parts Used:
- 216518000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken door handle.
The important part was the parts delivery. Ordered one afternoon received the next afternoon. Very impressive!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Star Lake, NY
- Parts Used:
- 297147700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed a freezer key
We really didn t need to do a repair, we just ordered a freezer key that we didn t have. I must say the shipping was fast we received it the next day. It was worth the shipping charge. We will be ordering again. Great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from San Marcos, TX
- Parts Used:
- 297216600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer would constantly run. Even when it was super cold inside.
I ordered a new thermostat and installed it in less than 15 minutes. Looks like the problem is fixed. Now ,the freezer cycles on and off correctly. The part was ordered on a Monday and I got it the next day. I am very satisfied.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Tahlequah, OK
- Parts Used:
- 216486500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
stop-basket was broken
I stuck the new stop-basket in the hole where it belonged.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott J from Westminster, CO
- Parts Used:
- 301036
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Side rail for sliding shelf would not stay tight
The sliding shelf side rail is held by three philips head screws that tighten into nut inserts. No amount of tightening would keep two of the three screws tight. I found that the nut inserts which are plastic and insert into the side of the freezer would pull loose, probably from years of overloading the sliding shelf basket. Ordered two nut inserts from PartSelect. 1. Remove three screws to remove shelf slide side rail. 2. Remove nut inserts to be replaced with needle nose pliers or reinsert screw a couple of turns and pull nut insert out with pliers. 3. Insert new nut inserts, position side rail, and tighten screws. Replace sliding shelf/basket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from noble, OK
- Parts Used:
- 297147700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lost key
Ordered freezer key friday afternoon received it saturday afternoon. Fast service
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Augusto from Gretna, LA
- Parts Used:
- 297216600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
thermostate stop working frozzen up
just like the video show sa 1,2,3 yeaaa thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wilson from indialantic, FL
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
compressor not running
thanks to all of the people who had the same problems I was able to make a quick fix on my fridge. I pulled the back cover off and found the compressor not kicking on so I replaced the start cap. and im back in bussiness.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bart from goldsboro, NC
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the compressor capacitor overheated
it was great. I ordered the capacitor for my frigidaire frig and it arrived
in 3 days. plugged in the part to the compressor and my frig has been
working ever since. I spent 3 minutes ordering the part and 30 seconds
attaching it to the frig. Easy, very easy. saved myself a 75 dollar repair
visit. thanks
in 3 days. plugged in the part to the compressor and my frig has been
working ever since. I spent 3 minutes ordering the part and 30 seconds
attaching it to the frig. Easy, very easy. saved myself a 75 dollar repair
visit. thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Hudson, FL
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
not cold enough
per the video..easy installation....unfortunately the temperature did not improve. We still have a refrigerator temp in the upper freezer.....and a "cooler" in the refrigerator section
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANK from BRADENTON, FL
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Frige and freezer not cooling
I should have ordered start kit instead of start capacitor. The start cap astir did not fix problem so I ordered kit. Compasator comes as part of kit. Followed enclosed instructions. Cut existing wires and reconnected new wiring. Simple as that. It's a plug in item. Now worried it may be working to good. Freezer down to 10 deg. Watching to see if compressor is running to long. Seems ok lol. Wife hates me now. She wanted new frige.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Winlock, WA
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
won't start repaced the run capacitor didn't solve the problem so I ordered a defrost timer
I watched the videos (they really help) and followed the steps. Everything went smooth with no surprises
Was this instruction helpful to you?
Thank you for voting!
Freezer only cold on bottom
Pulled freezer out from where located to allow shelves to be removed.Unplugged unit, removed shelves and evaporator cover, installed new fan motor. Plugged unit up to check fan motor operation. Reassembled unit, installed shelves and moved freezer back into original location.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from GAINESVILLE, GA
- Parts Used:
- 297013500
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replaced drawer slides L & R
Removed three screws each side to remove old slides. Needed spacers under new slide so that drawer would stay on track. Cut old slide to make spacers and installed both slides in 15 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CRAIG from PRESCOTT VALLEY, AZ
- Parts Used:
- 297309000
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Noisy fan
Remove the cover panel inside the freezer, remove and replace the fan motor (pull fan blades off old motor and push on the new one) and replace the cover.
Was this instruction helpful to you?
Thank you for voting!