AFFU2068DW0 Frigidaire Freezer - Instructions

Both end caps were missing on the door side bottom metal shelf. succesfully installed no tools needed

Removed existing part, tested it, found it to be defective. OrderEd a new one and replaced the existing one.

Ice maker is held by 2 screws just above the unit, on the wall of the refrigerator. You can't see the screws, so borrow your wife's makeup mirror. Shine a light into the refrigerator, and using the mirror, locate the two screws, holding the unit in place, on the wall of the refrigerator. Using a nut driver, or socket wrench, with a 1/4 in socket, loosen up the two screws, but don't remove them. Bump the unit upwards, and away from the screws. (BEFORE doing anything!! Shut off the water supply, unplug the refrigerator) When you get the unit freed up, just unplug the old unit, and install the new one. You don't even have to worry about the water lines, and you'll see why, when you get the old unit off. Just reverse the procedure, installing the new unit. Very Simple, 10 to 15 minutes tops.

Followed the instructions

Remove ice pan below ice maker. Got mirrow verifed the type of screws. Obtained nut driver and felt it at right angle remove screws only have way. The ice maker lifts up and off. Took needle nose pliers to grip and remove electrical connection plug. The instruction and picture sent was no help the picture were the size of a thumb nail no detail could be determine. I installed the adapter plug and all the extra length wiring was the most difficult to type wrap with both hands extended out in front. I finally wrestled it in on to the two screws unscrewed from the wall about 1/2". Keep the ice maker water lever up and ensure it aligns to the water trough inlet. Works Great.
glg

After pulling the fridge away from the wall and opening the paper backing on the bottom, I could see the motor. It's affixed to 3 metal ribs by 3 small screw/nuts. There is also a 12" wiring harness that led to a simple disconnect. Removing the disconnect and the 3 nuts was easy. However, there was no room to remove the motor with the fan attached. Between frame parts, the drip pan below, the ribs, and small, delicate copper tubing that can't get bent, it wouldn't fit thru any openings. So we rotated the motor inside the framework until the blade faced out, then reached in with a pair of needle nose pliers to remove the washer. Removing the washer is easy, it's just difficult to reach. With the washer off the fan was out of the way and very carefully (it was tight) the motor came out. Reverse was the same issue. Motor tight going in, not a lot of room to maneuver fan onto motor, and needed needle nose to tighten washer again. Make sure you tighten the washer before you install the motor on the prongs. Otherwise you need to remove it from the ribs, twist it to face you, then reinstall it on the prongs. Also, I felt I was stripping the nuts into the new motor. Turns out the holes in the motor aren't tapped. i realized the nuts are self tapping once I looked at them. I'm a big time DIYer and this wasn't bad at all. If your motor/fan assembly comes out whole, it's even easier.

Real simple repair..just backed off the two 1/4" hex bolts holding the ice maker to the wall of the fridge,(a little tricky since you can't see them),unclipped the electrical doo hickey. I re-clipped the electrical do hickey of the new ice maker, hung the ice maker on the bolts and then re-tightened them. However,still no ice,my problem was the water valve on the back of the fridge behind the cardboard. Although it was still giving H2O thru the door it was not allowing water to flow to the ice maker. I reccommend pouring some water into the ice tray of the ice maker. If it makes ice and dumps it in to the holder, your ice maker is OK. If it turns out to be your water valve, that fix is easy as well. I HIGHLY reccommend watching the "fix it" video associated with that part. That repair also took less than 15 minutes. Good Luck! KC Bridgewater,NJ

Had to reach right hand to top of ice maker to locate hex head screws by feel, then place nut driver onto hex head by feel and then unloosen screws with lft hand ,a couple of turns, enough to lift ice maker off screws.
Replace new icemaker onto screws and tighten screws. The only problem incountered was the location and availability of having to feel with both hands to fit nut driver onto the screws.(could not see with my eyes because front of ice maker blocked view. )

Loosened the two mounting screws (no need to remove them), lift off the icemaker and unplug it. Reverse the order and done.

After removing the key from its shipping package I pushed it into the freezer locking slot and turned it to lock and unlock the lid and then removed it. I had no problems with this fix. Of course, I am an older gentleman with a lot of experience in repairs around my house,as well as other houses. I am sure that a less experienced person may have more of problem with this type of "repair".

I removed the two side mount screws with a screwdriver and disconnected the electrical plug to the ice maker to remove it. I reversed the process to install the new one.

It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.

easy change less than 10 min

Remove shelves. Unplug unit. Unscrew back panel. Remove wire harness. Remove old fan. Insert new fan. Screw it in. Reattach wires harness. Plug unit in and make sure fan is on.
Reattach back panel. Put shelves back in.

removed old broken part, 3 screws, then installed new part.....done

The ice tray would fill up, but never spit the ice out. I pulled one screw out of the bottom of the ice maker and loosened the two on top. I dropped the unit, unpluged the power and reversed the previous steps to install the new ice maker. Completley easy.