FFU14F9GW0 Frigidaire Freezer - Instructions

It took just a few minutes after getting the parts to replace the cracked door handle caps - they fit perfectly!

No repair. The key fit!

Unscrew all the fasteners from the door inner cover from the bottom to top to hold it in position, got rid of the old gasket.

I Cleaned all and install the new gastket into the door inner cover. then reintalled cover to the starting from the top to bottom to hold it in place.

this is a one man job but with two will be easer

Brought replacement key works just like original I thought it would be metal from reviews but it was plastic and still works perfectly

It's easy to know how to use a key. I didn't have a difficult part, I didn't have the model # because I had lost my key and the model # is inside. I was able to find the energy saving paper that came with it but it had four model #'s. I called a couple places and no could me. I pulled up Part Select on line and just thought I would give them a try. I got a very nice person (Jeremy) He went thru every model that I had and three out of the four matched so he sent me a key and if it didn't work I could get my money back. I give him a A+ four taking that extra step, unlike the other places. Very satisfied!

Oh yea thanx to partselect it went great didnt get fisrtkey but when got the second key it worked great thanx partselect

Notice ice build up on the panel in front of the evaporator coil. Unplugged freezer and removed evaporator panel. Plugged unit back in and checked fan, coil "snap switch" and heater element, all seemed to check out good. Found defrost timer stuck in the freeze position, causing frost to accumulate over the evaporator. Manually rotated defrost timer to the 30min defrost cycle and system went into defrost. Ordered defrost timer and installed (part arrived in 3 days). Freezer works great again. Too bad I ended up throwing 400 dollars worth of meat away. the fix was very simple. Will definitely use PartSelect again. Thank you.

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .

This was an easy job. First remove the ice maker, if you have one. Mine was mounted with just two screws. Loosen these screws, unplug the power cord at the connector and then lift the ice maker off. Remove the light bulb cover and the light bulb, just so you dont break it. Remove two hex screws and the back cover can be removed. My fan was mounted in the middle of a bracket retained between two rubber bushingings. Just push the fan blad of the shaft and pull the motoer out. Dissonect the power cord at the connector. My moter was differant than the replacement on the mounting so with the removial of the two screws on the motor I was able to exchange the upper and lower cast motoer housings. Reverse the assembly process and you good. Mine is running great.

Removed bottom cover , just two screws , slid old part through install hole and removed wires from old switch and installed on new switch. Installed new switch in same hole and pushed gently until it locked in place. Reinstalled bottom cover and done.

inserted key and turned

Took interior panel off and uncliped yhe termination switch and cliped the new one on the coil and connected the two wires very simple. The defrost timer was located in the rear of the unit on the right side at the bottom. Removed the 2 screws holding the bracket unpluged the timer and removed the timer. The new timer allready had a bracket so just plug in and install the 2 screws. Pluged the unit in and worked great make sure that the freezer is unpluged before changing any part

We really didn t need to do a repair, we just ordered a freezer key that we didn t have. I must say the shipping was fast we received it the next day. It was worth the shipping charge. We will be ordering again. Great service.

The important part was the parts delivery. Ordered one afternoon received the next afternoon. Very impressive!!

Removed 2 screws holding front bottom vent grille. . Through opening behind grille found broken part of switch hanging on wires. Removed wires from switch and fed them out through hole for mounting switch, connected wire and pushed into place. The greatest difficulty encountered was my 82 year old knees.