E32AF75FPS0 Electrolux Freezer - Instructions

Took off cover, unplugged wires, removed old motor, mounted new motor, remounted new motor and replaced cover.

Now need a new control board for same model.

1st Turn off power. Removed freezer racks. Removed access panel to bottom back of freezer. Disconnect the wire harness to fan motor. Use 5/16 nut driver for removing fan motor from support. Removed fan blade from motor and put fan blade on the new fan motor. Bought new fan blades, but new fan blade would not work on new motor. Spring mount would fit on new fan blades, so I use the old one. Installed everything in reverse. Put everything back. Place thermometer in freezer. Freezer cooled down to -10F in 10 minutes. Great save on this one because I bought this freezer off of Facebook marketplace. Saved me $250. Good thing I know about fixing refrigeration equipment. Easy day.

freezer section remove ice trays ,shelves,unplug ice tray.use 1/4 nut driver remove back panel,use hair dryer thaw ice from evap coil ,unplug tstat remove install new one.plug in ice maker,put back panel back on ,ice maker and shelves plug refridgerator back in

Pulled unit away from wall and shut off water and unplugged unit. Installed water valve and reassembled, plugged back in and turned on water and checked for leaks. All good. However there is no water getting into the ice maker. The unit itself is going thru a cycle of attempting to make ice and the bail is moving and you can hear the solenoid activate but no water. I have tried to blow thru the tube going to the maker but it seems to be plugged by something. I do not know if there is another valve up there or how to clean it out. Any help would be greatly appreciated.

The first order arrived in a huge box and there was no scew to be found, the box had wholes in it. I was given a refund and told to order again.



The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.

installed new ice maker. Was very esay - the only problem I had was the length of the wire, due to the need to use the adapter, was hard to menauver around so that it didn't contact the bottom of the ice maker. Would be best if it was configured so that you had the right wire connection and didn't have to use the adaptor.

The repair took only 5 minutes. I removed the ice bin, which just slides out, then loosened 2 screws at the back-top of the ice maker. I then unplugged the broken ice maker, removed it, put in the new one, re-tightened the screws and plugged it in. It was making ice within an hour.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)

The best thing about the whole experence was I recieved the part the next day and it was so simple.

Loosened 2 screws, lifted icemaker brackets off of loosened retaining screws, unplugged electrical connector from the icemaker.
plugged in the supplied jumper harness & connected to the new icemaker, hung it on the loosened screws, secured the 2 screws.
Dranke beer & listened to my new icemaker rock & roll.
No further problems, Frigie like new.
The price was the cheapest I could find. $78.00 total including shipping.
A little girl could replace this unit.

Turned off water, unplugged refrigerator, Removed defective unit with support bracket. Installed support bracket, adjusted flow screw per instructions, plugged in wiring with adapter, hung on screws, tighened screws, secured excess wiring harness (making sure it did not hang below icemaker per instuctions), turned on water, plugged in refrigerator. Comment it took a few hours to start making ice, air in line? After a couple of days seems to be working fine.

LOOSENED THE TWO SMALL SCREWS THAT HOLD THE ICE MAKER UP INSIDE THE FREEZER. DISCONNECTED THE WIRING HARNESS. TOOK THE OLD ICE MAKER OUT AND JUST INSTALLED THE NEW ONE IN REVERSE ORDER. LATER THAT DAY I HAD FRESH ICE FOR THE FIRST TIME IN WEEKS!

The service man that I hired to fix my Ice maker removed the broken one. This is how I saw how easy it was to install. When the new one arrived all I had to do was plug it in then tighten 2 screws with the right size nut driver. This was the hardest part of the install havng the right tool for the job. Now I have Ice!

It was just a simple replacement, three nuts to loosen , a slight adjustment on the timer and reversal installation...As simple as replacing a light bulb! You needn't be a brain surgeon to do this job! Your installation video was very helpful....Thank you PartSelect Chuck McCann

Took about an hour previously to deice freezer, timer was running,drain was open, jumped defrost thermostat out and heater was O.K. Defrost thermostat was just a plug and play item, the time involved was in taking the freezer apart to get to it.

The screws holding the ice maker in place were backed out about a turn and a half or so. The icemaker was raised about 1/2 inch to clear the bolt heads. The icemaker was extended just enough to access the wiring harness connector. The connector was released, and the ice maker was removed. The replacement unit extension was unneeded. The wiring harness connector was attached, and the wire was wire-tied out of the way. The icemaker unit was placed over the screw heads, rested in place and the screws were tightened (only snug). Easy-peasy!