E32AF75JPS0 Electrolux Freezer - Instructions

Remove the cover panel inside the freezer, remove and replace the fan motor (pull fan blades off old motor and push on the new one) and replace the cover.

Remove back cover (5 screws )remove valve ( 1 screw ).Disconnect in and out water lines. Disconnect wire on solenoid. Install in reverse. Dont forget to turn off water.

TURN OFF WATER!! UNPLUG REFRIGERATOR!! Remove water fittings and electrical connector on old valve. Remove two mounting screws on pump bracket. Reverse procedure to install.

I ordered a new thermostat and installed it in less than 15 minutes. Looks like the problem is fixed. Now ,the freezer cycles on and off correctly. The part was ordered on a Monday and I got it the next day. I am very satisfied.

just like the video show sa 1,2,3 yeaaa thanks

pulled out freezer, went to floor,reached in next to compressor pulled off clip just like on the video.Pulled off old capacitator took off wire leads.Installed new one. Freezer runs great.Loaded it up with beef pork and venison. No problems.

Took out three shelves. Removed 9 screws with a battery powered drill with a phillip screwdriver bit. Popped off the thermostat like I had seen on the video. Put the new thermostat on. Replaced the two wires one at a time. Reassembled the unit. This was so quick that my wife told me to let her know when I wanted to fix the freezer. She was shocked that I had completed the job. I'd been in the garage less than 10 minutes. It has been six weeks. and the freezer is working perfectly.

I replaced the defrost timer,defrost thermostat,and run cap.as it turned out the compressor went bad. I dont know the model because but the time I got this review I replaced the refer with a knew one . two weeks living out of coolers was so much fun !!!!!!!!

it was great. I ordered the capacitor for my frigidaire frig and it arrived
in 3 days. plugged in the part to the compressor and my frig has been
working ever since. I spent 3 minutes ordering the part and 30 seconds
attaching it to the frig. Easy, very easy. saved myself a 75 dollar repair
visit. thanks

Removed water line. Removed two screws holding valve. Disconnected line from valve going to Ice maker. Replaced screws and water line. Most important thing in working with Parts Select was the information they provided when I called them. I had called electrolux and was given no information and was told they would send out a repairman at which point I told them to get lost. Cost of part $30.00 vs service call of $75.00.

Old part threads : made in China (brass) New part : made in Mexico (steel). First, unplugged it from the wall. As for the valve, removed the two screws holding the valve in, disconnected the plug, took the pipe cutter, cut the blue line to the ice maker, cleaned up the cut, pushed that line into the new one and reassembled. Done!

Unplug freezer let stand all night to defrost. Remove the tray cover which is located on the upper back area inside the freezer.( 3 twist fittings remove it ). Remove the upper stainless steel panel which is secured with 6 screws. This will drop down exposing the condenser. Note all the wires and fan will stay attached to the stainless steel panel, this panel will drop down no need to unplug anything. On the left upper side next to the condenser you will see the thermostat. Two color coded wires. Remove the thermostat and install the new one at the same location.

Installed new fill valve in less than 30 minutes and waited for 24-8 hours for results to no avail. Ice maker mechanism was shot and still would not work. Went to Lowes and bought entire ice maker add on kit for my model ice box and installed in 30 minutes and have been making ice ever since. Your 99% cure rate was 100% incorrect. Save the time and effort and go to a big box store and just get a new ice maker. By the way, it only costs about $20 more to do that.

I unscrewed the screws that held the old fan on, disconnected the wiring harness and removed the old fan. I pulled the blades off the motor and put it on the new fan. One thing of note, the screw holes on the new fan weren't threaded. I assume this is by design, so I used the screws to thread the holes before installing it in the freezer. Once I did this, the rest of the installation was easy, just screw it back in and connect the wiring harness.

inspected visible refrigeration lines for evidence of leaking, found nothing substantial that would cause concern, ordered capacitor and defrost thermostat simply because both are inexpensive parts and theoretically either could be causing the problem. Both parts were very simple to install especially since I am a semi-retired refrigeration man.