AFU1705BW Amana Freezer - Instructions

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

Viewed the viedo - it showed what to do

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

Removed door. Laid door down on a table. Unscrewed all screws around outside of door. Removed plastic cover back of door underneath cover was filled with heavy ice apparently from condensation. Cleaned and dried back of door really well. Replaced with new seal. Reinstalled door. New seal works perfectly.

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

I unplugged and defrosted the freezer ( good excuse to give it a good cleaning). I then removed the hex screws from the door under the gasket. Because this attaches the door panel to the freezer, it is helpful to have two people for this task if you have a full size upright freezer. We then removed the panel, cleaned the door, and fitted the new gasket in place. If your gasket has kinks in it, either throw it in the dryer on low for a few minutes or use a hair dryer to smooth them out. We then added a few screws around the center point of each side to hold the gasket in place, secured the corners, and replaced the remainder of the screws. We used a small cordless drill. The gasket will be hard at first, so I duct taped the freezer door shut with a few pieces of tape and turned the unit back on. A repair guy was going to charge me $350.00 for the job, but I did it for free with the cost of the gasket. This site is the least expensive place I found anywhere, and shipped very quickly!

put the new gasket in a tub of hot water. remove door and lay on flat surface, remove old gasket and pull hot gasket from tub, dry and install, the hot water helps remove the wringles from shipping.

After unplugging the microwave and removing the screw, I removed the old bulb and put in the new one!! I made sure it was in securely and the difference in the light was awesome! I use this light when I bake bread and let it rise inside the microwave, but DO NOT turn it on. The heat from this light helps the bread to rise properly!!

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.