YWED87HEDW1 Whirlpool Dryer - Instructions

After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back together in reverse. I also took the time to clean any dust and lint out.

YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!

How to repair E1 error/fault on Whirlpool Duet dryer model GEW9200LW0 please watch that video very helpful.

Followed standard instructions regarding removal of top first & then the front panels. Realized after following this process that I did not have to remove top, but only one of front panels to obtain access to moisture sensor. If I have to do this again, the replacement of sensor will be much easier.

You tube and supplied video directions for the make and model. Follow step by step and the repair went easy. Worried when removing the dryer drum but it went smooth.

Unplug dryer from 220VAC outlet

Remove bottom cover panel, slip a flat blade screwdriver into each clamp, and bottom piece becomes removable. Pull forward and lift bottom cover piece.

Pull up top section from dryer frame. Disconnect dryer door off/on contact three wire switch by pressing plastic connector together. You may need a small flat blade screwdriver to seperate connector.

Remove two Torx (T15 head) screws in the far left and right corners of the front door panel.

Remove two screws underneath dryer lint screen, be careful to not let front door and front cover fall forward. The rotating dryer drum will now be loose.

Underneath drum, there is a cover panel over the dryer motor. Likely you will find a bunch of lint all about. This dryer had likely not been cleaned in many years.

Remove screws on dryer motor cover.
Remove panel. Likely, you’ll more lint about.
After vacuuming, use a flashlight and hand mirror to locate belt tensioner, back side of motor. If your belt is not broken, press down on the tensioner spring and remove belt from tensioner and motor. Inspect belt, replace if worn. In this instance the belt was well worn.

Slowly pull dryer drum forward, walking belt along as you bring drum forward out of the dryer casing.

At this point you have plenty of room to access the one bolt holding the tensioner, in this instance it was a 13mm socket. Be careful to remove the tensioner springs before removing the bracket. Your PartsSelect is an identical match to the original one.

Install new tensioner, tighten slightly, then put springs back on.

Reverse this entire process to get your dryer back together and back running smooth and quiet as it was when new.

This dryer was quieter than its owners remembered it being back when new 15 years ago.

Well worth saving the $ doing your own work.

Good luck on your repair endeavor!

Replaced heating element and went ahead and replaced the belt since the dryer was coming apart and belt taken off also. I used the parts select video and paused the video through each step to complete each step. There videos are great for this and as long as you pause and do each step per the video it is quite easy. I Highly recommend doing each step one at a time as I did not have a problem. Thanks for great repair videos.

Replaced 4 wheels and new belt

sounded like a pair of shoes was in the tub every time i started it no matter what size the load was. Replaced the back two rollers first and decided to start it to see how it sounded. We were glad. Only the back rollers were bad and the dryer was quietly running again. We would suggest replacing the back rollers first to everyone because the front rollers are more complicated to replace and they may not have to be at all.

I followed the very informative video and wrote down step-by-step notes for myself. The repair went very smoothly. The only thing I didn't realize, was that the dryer has 4 rollers, not just 2 shown in the video. All are easy to access once you disassemble. I had to do it twice since I had to order 2 more rollers in order to replace them all. Also, the triangle plastic washers come with the roller, so you won't need to order them separately like I did. I also changed the idler pulley roller while I was in there since that has bearings too. Just as easy. I'm very happy with my quiet dryer! One last note: The new rollers are a bit louder than normal at first, but they quiet down very quickly as you use the dryer. It must be because they are brand new.

Replaced the most worn drum wheel any lubed the belt tension arm pulley. The noise didn't go completely away. There are 4 drum wheels. I need to order 3 more wheels and the tension arm now.

Remove top,front and panels.change thermal fuse and outlet thermistor.

The repair went well, using the whirlpool repair manual and looking at the video from PartSelect. The machine was a bit different than the one in both the video and the manual but that did not cause any problems. The only tricky part was to reinstall the belt "blind" behind the motor, easy to pinch your fingers and also get scratched by the sheet metal edges. To make it easier for that part I supported the drum with the old belt and a bungee cord to the garage frame so I did not have to hold it up and work under it at the same time. When the drum and new belt were in place I just cut the old belt, it was going to the trash anyway.. I replaced the belt and the tension pulley, witch was not turning easy and worn by the belt. I also put some grease ( SUPER-LUBE, www.super-lube.com) on all pulleys. It took about 2 hours because I am 78 years old and have heart problems.

I found a simple video on YouTube. I removed the front panel and door. I removed drum and belt drive. Heater element was then easily accessible. I removed all wires after taking pictures of wiring. Element was secured by one screw and one clip and was easily removed. Removed element from element cover. Checked thermostat and thermal overload. Put new element inside of element cover. Then replaced everything in reverse order. Removing lint from inside of dryer was probably the most difficult part of repair. Had to have assistance from my son to put drum belt back on but rest of replacement was simple.

Watched video & took my time. It went easy