YWED8000DW3 Whirlpool Dryer - Instructions

Installed new belt and cleaned dust and wiped out inside of drum with Fantastic and clean sponge.

Removed the lower front cover of the dryer. Removed the lint filter and removed the cover from the air duct by removing two 1/4" bolts. Removed the two 1/4" bolts retaining the thermistor. Installed the new thermistor and covers.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Took off the front of & lifted the top up. Pulled the drum out & replaced the two wheels that turn the drum, replaced the belt & replaced the pully wheel that turns the belt & dryer motor & put back together. The dryer now runs like a new one. Has no noise when running.

Remove the back cover from the dryer after unplugging unit from electrical outlet. Remove the belt by moving tension arm. Remove the tension spring (by hand). Remove the idler pulley bracket with a nut driver. Remove the Tri-Star retaining clip with a screw driver. Remove the old idler pulley. Remove old washer... replace with new washer and idler pulley... I could have reused the tri star retaining clip but elected to use new one. Put arm back on, re-hook spring, realign belt, put back cover back on... dry clothes.

This was by far so easy the instruction Partselect gave me where right on step by step. a repair man was going to charge 75$ just to come out 9$ from partselect. Thank you very much Mike chaplin

My husband changed the idler pulley. It took him 5 min. Thank you sooooooooooo much. Saved us 1000.00 dollars. He wanted to by a new one but investigated the problem on line. He is a handyman and was just being lazy. I ordered the part and he fixed it. I love saving money!!!!!!!!!!!!! And I love my husband!!!!!!!!!!!!!!

Simply slid new idler wheel on then popped thr tri ring on. The belt replacment was the hardest thing which was also easy. I think pulling the dryer away from the wall was the most difficult thing.

I replace the terminal block, wires , and dryer plug I unscrewed the back of the dryer and basically replace was burnt out. I was about to pay 200.00 to have it done but I looked on youtube and seen how easy it was so I just chose the site to order what I needed to be replace and it arrived quickly and more affordable to do it myself. Thanks I hope the was useful.

We only had to tilt the dryer enough to be able to screw the leveling leg in place.The only hard part was holding the dryer steady to screw in the leveling foot.

Broken belt, but went with the mainentance kit since it was going to be all apart anyway. Found the job easy to do and the new belt idler was a big improvement over the old style. /also came with instructions. Good for another 5-10 years.

The repair went great . Thanks for the part ,will be purchasing parts from you now on.

Belt was worn, rollers were sticking, idler worn out. Ordered a kit to care for these issues, as usual the reapirs took almost no time. Dryer became a bit quieter for a first load, second load the motor siezed. I priced rebuilding most of the machine and determined replacement was due.

Diagnose the problem. Is it the motor ? Is it the belt ? Order the correct repair kit, use name brand parts to ensure reliability. READ THE SUPPLIED DIRECTIONS. You can use a small wood shim or wedge at the top front corners to open the top . Use a 5/16" socket to remove the 2 screws at the top outside corners. Lift the front panel straight up, supporting the drum as you lift it off. Remove the drum, taking it straight out the front. Install the new drum rollers, install the idler, and then the belt around the drum. Install the drum on the rear rollers, make sure the seal is not folded under. Push the drum back against the seal flange, support the front of the drum with your right (or left ) hand, and sit the front panel on the lower pins, and gently push the front panel to the sidewalls. Feed the belt through the idler and around the motor pulley. This job is easily performed in about 20 minutes. Clean the interior while replacing the belt/idler and drum rollers. With the top lifted, after assembly, test run the dryer to make sure there are no "funny noises" after the repair. Watch especially for the white rub strips on the front edge of the drum. They tend to fold over when attaching the front panel. Job done !

Thank you for your part service. It saved me about $ 200.00 dollars by Sears not coming out to repair a simple problem.