YWED75HEFW1 Whirlpool Dryer - Instructions

Unplugged the Dryer first. Removed the two screws from the bottom panel using a 1/4 socket and removed the panel by pulling down and out. Reached behind the blower and removed the connectors from the old thermistor and then the thermistor itself by removing the two 1/4 inch hex head screws. Replaced with new part and after screwing back in, reconnected the wires and replaced the panel. From start to finish, it took me about 20 minutes.

Since I have All Whirlpool appliances in the home, the only one not a Whirlpool was a counter top dishwasher that looks exactly like it could be a Whirlpool and so not to be the odd unit out, I labeled it with with a Whirlpool logo nameplate on the face of the door. Now everything matches perfectly and all in the same exact color white too.

Just measured and marked where the plate was to be located, cleaned that part of the surface, peeled the backing and carefully placed the logo name plate in place and pressed it on. Voila. Done and looks original as well. Call me the big, deep fakearooski.

I just took the old element replaced with the new one i order from this site, I save some money was really easy so proud of my self...

I researched causes of the noise, zeroed it down to the idler pulley. I then got the dryer schematic and took the dryer apart after disconnecting the power and the vent. i did not have to remove the drum, the idler pulley was easily accessible once the top and back panels were removed. I simply removed the drive belt from tension off the pulley, removed the old pulley and installed the new one. Once finished the dryer was running whisper quiet.

pull the back off and replace the pulley.

Disassemble dry. Put on new pulley wheel. Greased pulley wheel. Put dryer back together. Works great. Yours truly G.B.

Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger

It was a lot easier then I thought. Just watch the tutorial of how to fix it on this website and you wont have a problem.

Took back panel off, and it was really easy putting the new idler pulley in.

Very easy repair... The video was really helpful too. I was able to find a different video that was closer to our model. (Front Loader HE) It probably took me a little longer than needed but I took the time to shop-vac everywhere I could, since it was all easy to get to. I opted for next day shipping so the shipping charges were more than the part. Tools I used were: Cordless drill-screw driver, 1/4in. socket, Phillips head bit and needle nose pliers for the control panel connections. Thank you again for making this so easy. Saved us a lot money by not calling an appliance repair tech.

Seemed daunting but pull the front off and the drum is basically just perched inside on some rollers. You have to pull it out to really reach in and wrap the 96”+ band around it and to motor and don’t forget to tension it with tension pulley if you don’t see that if your belt broke!
Another bonus is after 10 years I got to remove the softball size fur ball rolling in the squirrel cage fan , big help on air flow!!!

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

The first thing I did was to watch the video from Part select on How to change thermostat cut off switch and the high limit thermostat fuse.I did not have a meter reader I just brought the thermostat cut off kit for about $ 32.00 dollars from part select and replace both part's and my dryer still was not getting hot so back to part select video's I looked up the video on replacing the heater element and I ordered one for about $ 97.00 with shipping I replaced it and put it back together and it worked it took just a few hours . I would like to give Avery special thank to part select for the video help and for having the parts for a great price again thank you so much.

I removed the top first followed along with removing the side bracket that holds the circuit board. I then proceeded with removing the bottom cover and front panel. I disconnected the front panel from the control board and was able to slide the front panel upward. The door and blower housing was a bit tricky to pull out without thinking I was damaging something. I then replaced all the seals and cleaned the dryer after removing the drum and belt. I also replaced the drum support rollers. Afterwards I put everything back together and had an "E1" error and I pulled the thermostat out and wiped it down from all the lint and dryer worked perfect after that. Dryer takes the right amount of time to day clothes and no more rumbling noise. The instructions videos were VERY helpful.

Lubricated pulley wheel which temporary reduced noise. This verified what was making noise. Looked up the part on partselect.com and ordered it. Recieved idler pulley with bracket in just a few days.
Quickly removed back panel using nut driver with drill. Slipped belt off pulley, removed one screw with plyers to released spring and removed old assembly.
Inserted new assembly, connected spring, slipped belt back on roller.
Tested before replacing back panel.
All was very quiet. Replaced back panel.
All done