YWED7300DW0 Whirlpool Dryer - Instructions

Unplug unit first.
Took the front cover off the front of dryer below the door.

I Picked up the two front corners up, after removing the 2 screws from the vent and the 2 screws that hold the door switch in place, then I disconnected the old switch and put in the new one. Just the opposite of how I took it apart. Very simple and it works great!! Thanks

The original door catch had broken and would no longer stay shut. Ordered the part from this site with ease. Very easy to replace the broken door catch on my Amana dryer. Tool needed was a flat head screwdriver to loosen the cover, remove broken piece and easily replace with new part. Followed the video and it was back to normal operation within minutes.

Kill power to dryer from breaker box.Remove lint filter & 2 screws. Take a flat head screw driver and place in gap between rash from corner of top panel & front panel of dryer and pry up to raise top panel of dryer & rest against wall the wall on angle do it doesn’t fall back toward you. Unplug wiring harness from dryer switch inside top front corner of dryer with outside of drum exposed when top panel of dryer is raised. Open dryer door and remove screws on each side of dryer switch located at upper inside corner of door opening. Take flat head screwdriver had slide in between connector & wiring harness on dryer. Remove old switch. Reconnect new dryer switch to wiring harness & remount switch to inside of dryer door opening. Lower top panel of dryer & press front corners of top panel to front panel of dryer & clips will be locked in place. Replace screws in dryer filter mounting holes yo top panel & replace dryer filter in place. Turn on power ‘ & check if light is working 1st. Then, turn timer knob clockwise, close door and listen if the drum is turning. Open door to see if drum turns. If both work, the job is complete.

As seen in video, All Good !

Our dryer quit heating and I feared that I would have to buy another one as I have never worked on a dryer. But figured I would go online and see what I could learn. Parts Select gave me the info that I needed.
Not being sure which part was bad I decided to start with the one time use Thermal fuse. When I noticed that it only cost 7 bucks and my wife had been complaining that the dryer had not been heating well for a while I figured I would go ahead and replace themostat. I ordered the thermal cut-off kit and replaced both parts. I put them on and plugged it back up and it is heating fine. I found the videos very helpful in showing how to do this.

After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back together in reverse. I also took the time to clean any dust and lint out.

Installed thermal cut-off kit. Dryer works fine now. Kit very easy to install.

I watched the video or I would have likley just called a repair man. It took longer to clean behind the dryer than to install the new thermal fuse. After taking the back off the dryer is was as simple as changing a fuse. Dryer works like new for about $20 bucks and we avoided the hasle of getting a repair man, especially since we live in the country. Thanks for having a web site that is so easy to use and full of good information.

unpluged the dryer, took off the back, followed instructions and was able to take of the problem on my own.

first, I read the other repair stories and used them as a guide.I checked to see if the heating element was broken. It was not. The Thermal Cut off Kit was the ticket for me. I replaced the three easy parts it contained. Repair time was 30 minutes tops that includes checking the heating element and removing and replacing all three possible culprits (of the Thermal Cut-off Kit). Thanks a million. Happy Ending!Oh by the way, my dryer now dries super fast(saving me a bundle)

Used the video to remove the top and front. Removed the drum. Removed the spindle through the whole next to the spindle. Vacuumed a ton of lint in the dryer and vent pipe. Reassembled in reverse order. Easy repair and a good time to clean the lint.

Removed the dryer's back panel and took a look. Had no idea what to do next, so I read up on it. Partselect was extremely helpful to me, the exploded views with the part numbers called out were particularly helpful. So I determined it was the thermal fuse. Unscrewed the screw holding in the fuse and disconnected the electrical supply. New fuse went in really easily. Job took a lot longer than it had to cause since I was in there, I cleaned out the dryer really good.

Why the fuse blew was interesting: had an extension cord routed over the dryer, well it was situated such that it caused the timer knob to bind up. Apparently, the dryer ran all night because of this and blew the fuse. So don't obstruct the knob or you will be replacing a thermal fuse!

Removed old seal and replaced with new one. Save yourself time and get some acetone to remove old glue works great!

Two Phillips screws, and 2 5/16 bolts and the dryer is open for this repair. Remove the drum and note the placement of the drive belt. Then using a pipe wrench grab the rear plastic fan housing, at the rear of the motor shaft, and turn the front of the motor shaft CLOCKWISE. If the Fan is ceased (as it was in my case) you will need to use locking vice grips (at least 3 or 4 between the fan blades to stop the fan blades from turning on the rear shaft.) while your turning the front of the motor's shaft. If done properly, you should have about 25-30 turns before the motor is free for replacement.
Once this is accomplished, mounting the new motor back into the dryer is a simple matter of reversing your steps. But keep note of the belt placement and the motor wiring placement before starting.