YNED7200TW0 Whirlpool Dryer - Instructions

Callled the service company to diagnose the problem. Watched him take machine apart. He found the problem. Told me the parts that I needed. Didnt know what they were. Went to partselect.com looked my model up and found parts and ordered. Followed same steps as repair guy: Two screws in back of machine then slide top off. Six screws in front to remove front door ( 4 screws on top 2 on bottom) Changed the thermostat and thermistor. Saved 320 dollars :)

Remove dryer covers and locate heater assembly. Removed heater assembly and checked visually if the heater coil is opened, I verified this with an ohm meter. Heater Continuity was OK. Next step I checked the heater sensors. Thermal fuse with bracket had no ohm meter reading between two terminals[open circuit]. Order part#35001193 "thermal fuse" with bracket from "partsSelect.com." Assemble back in reverse order. Please note that the dryer heater was filled with lint and needed a good cleaning.

First remove the top of this particular dryer, to get to the necessary screws. computer is located on the left side, and 3 screws frees it up. Then disconnect the wires. Unscrew the board, and replace!! That simple!! Unfortunately for me the bad computer melted part of the wire harness. I called maytag and drove them nuts untill they paid to replace the wire harness. I learned two simple lessons. Buy the cheapest appliances you can find because everything is made like crap these days, and if you must buy the more expensive appliances, get the extended warranty because everything is made like crap these days!!!!! Thanks partselect.com for the info, and discount prices!!

top and the front had to be removed to get to the fan... the thermistor that sits in the exaust fan went bad... the heat would come on for a few minutes then turn off completely not getting to clothes dry.....

had to take top off to get to the front cover screws.Then took the screws out of front cover, pulled it off then pulled the drum out. Man at the amount of lent in the buttom and in the heating element area. Well, after removing drum I found the problem with the pulley. When I got parts to put back together it took a little time and thinking to find out how the pulley an belt went together(belt came off when pulley finally melted in half)with holding drum up to see what's going on. The pulley is laying down,with drum in and belt around it put belt on motor shaft then pull pulley up vertical wrap belt coming down on motor side around pulley. Then put it all together.

Had to pull the top off and the front of dryer with a few phillips screws and was able to get to the thermistor and I also replaced the heating coil because it was bad.The cause of the problem was because of a clogged up vent. It was a easy replacement.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Initially I remove the the back panel on the dryer to locate the heating element, but ,next to impossible to remove from this point due to mounting screw located on the blind side of the support bracket.

In order to get to these screw you will have to remove the top of the dryer which is secured with two 10mm screws in the rear. Then remove the control panel secured with four screws.

then I preceded to remove the front of the dryer secured with four screws on the top four screws around the door opening .I gently pull the front open and disconnect the door switch and lift up to remove. I was know able to gain better access to see the screws holding the element housing and support bracket. After removing the three screws I took a picture of the electrical connections for reference which came in handy for reconnection.
The spade connectors are difficult to remove and a flat blade screwdriver works best. Once the element housing is removed from the unit its just a matter of separating the two halves of the housing to gain access to the element itself.

The element is sandwiched between the two halves of the housing and is a bit tricky to reinstall.
It’s best to position the element in the upper portion of the split housing using the four securing screws and then align with the lower half . You then feed the element leads thru the receptacle and bend the securing tabs down and you are ready to reverse the take down procedure..

Dryer would not start but electronics were working.

Pulled top of dryer off; noticed the belt was loose but not broken.
Went in through the back (1 screw and removed the exhaust pipe/plate); noticed the wheel was broken and thus the belt had fallen off.

Ordered replacement wheel/arm.
One screw to remove old one, one screw to install new one...tentioned the belt. Dryer was good as new.

I removed the dryer top and saw that the belt was intact. (I had suspected the belt or something stuck in the exhaust fan or somewhere.) I watched a few youtube videos and took off the rest of the top plates and front door and inner structure that held the barrel. After i inspected and cleaned out the fan blades and exhaust areas, I looked at the pulley rollers (motor and idler rollers). The idler roller looked a little melted and chewed up. I replaced it with the new assembly. Also replaced the belt. Putting the barrel and new belt back on was harder for me than the videos indicated because the spring was very tight and the area to put my hands was small and didn't give me enough leverage. I eventually got someone to give me the third hand pulling the idling roller a little further over and the belt was back on. It didn't take me long to put the whole dryer back together. It is running fine now.

These are not instructions as much as warning that although it is a one-person job, the idler pulley assembly is not as easily manipulated with the barrel there. Doing the fix was straightforward: one screw holds it in place. The men in the videos seemed to have no problem with easily replacing the belt, but I needed help with the tight spring. Perhaps now that I've done it once, I could figure out how to reach around the barrel and yank the roller enough to replace the belt, but with the extra hand it took seconds and was super easy.

First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!

1. Unplug or turn off circuit breaker to dryer. 2. Remove two screws on the back of dryer that secure the dryer case top. 3. Slide the dryer case top to the rear of dryer and then lift to remove. 4. Electronic Control Board is located in the left side front corner, remove the three screws holding the Control Board and cover. 5. Unplug all wiring from Control Board and remove the one screw holding the board to the metal cover. 6. Reassemble with new Control Board in reverse order. 7. May you be blessed with dry clothes ever after.

This repair is easy. The only drag to this repair is you need to almost completely dismantle the dryer just to get to it. So keep track of your screws.........Look on you tube for videos to dismantle the dryer, you will need to take this down to the drum to change....Once I replaced the pulley, it was about 30 minutes later the dryer was operational again.

Self with you tube
app thanks.

I ordered a Maytag side vent kit, #12002641, I received a part #2003961.The kit had 2 vent pipes that were about 4" x 24" and an 4" Ell. $105.00. Both vent pipes were too long. I was desperate to get my new dryer installed, so I took the vent pipes to my cutoff saw and made the fit. I then found the right part PS2003058, on your website at a price of $36.22.