YMEDB835DW4 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- stephen from tewksbury, MA
- Parts Used:
- W11429587
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door catch had crackedt
took out old ,twisted in the new one it was nice to have the right part the first time!! thank-you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from BLASDELL, NY
- Parts Used:
- W11429587
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door catch broke
Remove the protective cover on door with screwdriver, pop out the old catch, snap new catch in place, replace protective cover
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wanda from SHELBYVILLE, KY
- Parts Used:
- W11429587
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would not stay closed.
Replaced door catch on dryer door. Followed video on Whirlpool website and it took less than 10 minutes. The dryer works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CREST HILL, IL
- Parts Used:
- W10837240
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Idler pulley seized
The pulley is accessible from the back of the dryer. Disconnect the gas line. Remove all the screws. Also remove the small plate that secures the line cord. Lift the back up and out. I was able to avoid disconnecting the water line. Take a picture of the pulley so that you will have a record of the belt routing. Release the spring and remove and replace the pulley and bracket. Vacuum out the lint. Plug in the dryer to make sure that it works properly before reassembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Travis from GARRETT, IN
- Parts Used:
- W10837240
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Very loud squeaking!
Couple screws behind the electrical panel at the top and the top pushed back and was able to remove front panel, and then it was pretty easy. Take the two screws on top front, lint trap screws . The lint trap vent needs to come off. Then the belt, drum comes out to access the idler pulley. I did replace two drum wheels, I saw there was 5. I would recommend replacing all of them, they didn’t move well…..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from KENNETT, MO
- Parts Used:
- WP8577274
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Shutting off and had to wait before could turn back on
Followed online video very easy and dryer works like new one....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from MUNCIE, IN
- Parts Used:
- 279640
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
dryer was making a grinding noise
I researched causes of the noise, zeroed it down to the idler pulley. I then got the dryer schematic and took the dryer apart after disconnecting the power and the vent. i did not have to remove the drum, the idler pulley was easily accessible once the top and back panels were removed. I simply removed the drive belt from tension off the pulley, removed the old pulley and installed the new one. Once finished the dryer was running whisper quiet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- braulio from FORT WAYNE, IN
- Parts Used:
- WP3387747
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Not heating up
I just took the old element replaced with the new one i order from this site, I save some money was really easy so proud of my self...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rory from LEESBURG, VA
- Parts Used:
- WP8577274
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Dryer kept throwing the E1 error indicating the thermistor needed replacement
Unplugged the Dryer first. Removed the two screws from the bottom panel using a 1/4 socket and removed the panel by pulling down and out. Reached behind the blower and removed the connectors from the old thermistor and then the thermistor itself by removing the two 1/4 inch hex head screws. Replaced with new part and after screwing back in, reconnected the wires and replaced the panel. From start to finish, it took me about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Linthicum Heights, MD
- Parts Used:
- W10837240
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Loud scratching noise, very loud
Lubricated pulley wheel which temporary reduced noise. This verified what was making noise. Looked up the part on partselect.com and ordered it. Recieved idler pulley with bracket in just a few days.
Quickly removed back panel using nut driver with drill. Slipped belt off pulley, removed one screw with plyers to released spring and removed old assembly.
Inserted new assembly, connected spring, slipped belt back on roller.
Tested before replacing back panel.
All was very quiet. Replaced back panel.
All done
Quickly removed back panel using nut driver with drill. Slipped belt off pulley, removed one screw with plyers to released spring and removed old assembly.
Inserted new assembly, connected spring, slipped belt back on roller.
Tested before replacing back panel.
All was very quiet. Replaced back panel.
All done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from NORTH HAVEN, CT
- Parts Used:
- W11429587
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Catch broke
Unscrewed the inside part of the door from the outside door shell. Removed the broken pieces of the catch and replaced it with the new one. Screw the door back together. Did not need to remove the door from the dryer cabinet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DW from ALVIN, TX
- Parts Used:
- WP8577274
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
F-26 Fault message
Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger
Thank You.
DW Pranger
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from ONEONTA, NY
- Parts Used:
- WP8577274
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
The dryer would shut off mid-cycle.
I googled the problem and determined that the thermistor was faulty. I found your web site from which I ordered the replacement part. The part arrived within a week. The replacement was not particularly difficult, but the space was very tight (without removing more panels and covers). I just kept at it and got it installed and the dryer works fine now. There are several pertinent videos on you tube, none of which were my particular model, but the combination of them led me to a successful installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from St. Louis, MO
- Parts Used:
- WPW10512946
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerald from LEBANON, PA
- Parts Used:
- 279640
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Loud squealing noise during operation
Turn off electric to unit.
Remove lint trap.
Remove lower cover below dryer door. 1 grey clip on either side. Bend upper portion of the clip down while pulling forward on panel.
Remove 4 1/4 inch bolts that hold blower duct to fan.
Push pulley upward while removing belt.
Use a small angled pick to remove pulley lock ring.
Install new washer and pulley. I added grease to pulley shaft.
Hope this helped. Good luck
Remove lint trap.
Remove lower cover below dryer door. 1 grey clip on either side. Bend upper portion of the clip down while pulling forward on panel.
Remove 4 1/4 inch bolts that hold blower duct to fan.
Push pulley upward while removing belt.
Use a small angled pick to remove pulley lock ring.
Install new washer and pulley. I added grease to pulley shaft.
Hope this helped. Good luck
Was this instruction helpful to you?
Thank you for voting!