YWED8500DC2 Whirlpool Dryer - Instructions

We did repair by first watching a you tube video, then jumping in an dgoing step by step through the video. While not exactly the same dryer, the steps were in sequence. We thoroughly sleaned out the dryer with the tub out before reassembly. Th eonly slightly tricky part was putting front piece back, but once we mad esure ot align the sides for squareness the dryer went back together smoothly, execpt for one dropped screw. that was fished out through the bottom panel. The dryer runs quietly and we can watch TV with the door open to the laundry room again. I should have done this a long time ago. It started out by sqeaking at startup, then grew worse over time. I recomend anyone with a friend should be able to do this. Now with Cell phone pictures it is even easier to remember where the screw go.

The repair went great . Thanks for the part ,will be purchasing parts from you now on.

Once I watched a YouTube video showing me how to do the job I ordered the part from you. Am so impressed with your fast shipping and best prices via the Internet. Thank you SO much! The water level switch was easy to install, it ws getting the cover on the washer back on that was hard for me since I am 68 yrs old and have a bad knee. Its why it took me two hours to do what most people could do in 20 minutes.

I highly recommend the videos on this site for repair information. It wasn't exact for the age/model of my dryer but very close. Remove the top panel and then the control panel. Remove the lower front panel and finally the door and main front panel. Unloop the belt from the motor and remove the drum. I found one of the drum rollers was bad, which was causing my problem, but I replace all 4 rollers, the belt, and the idler wheel. Sounds like it did when it was new! Find the video for your model and watch it!!

Removed existing parts and replaced with new high limit thermostat and thermal fuse kit,replaced flue and tested. Worked like a charm.

UNPLUG UNIT FIRST!!! Removed back cover. Make sure to note not all screws hold the back cover by closely observing the screw. Take a picture of the belt routing before removing from the idler pulley. Use headlamp or flashlight to light up pulley area. Remove belt from idler pulley by pushing idler assembly towards the right. Use small screwdriver to remove the existing pulley by prying off the existing tri-ring from the back of the pulley. You may have to "feel" the ring since it in facing away from you. Once tri-ring is removed, slide off old pulley and gasket or old second tri-ring. Replace with gasket first, then pulley then tri-ring. Reroute belt. Use picture if needed. Replace back cover.

Took the back dryer cover off and removed the lint cover all from the back of the dryer then replaces the Thermistor (held with 2 screws).

Watched steve on the video on changing the thermistor a couple times, it appeared to be straight forward replacement. Unplugged the dryer. . . Went through the front, my lent filter slides in and out from the lid so I had too remove two extra screws to detach it. After opening up the front it became very apparent my thermistor was not located in the same location as the one in the video. Dryer needed a cleaning (lint/dust) so I released the idler pully tension on the drum belt and went ahead and removed the drum/belt and shop vac/ blew with compressed air and shop vac once again. Gave my dryer a much needed cleaning since I had it apart. Put everything back together in about 20 mins. Pulled the dryer away from the wall and removed rear cover and presto there it was right next to the dryer air outlet. Replaced thermistor and replaced back cover, inspected out flex hose on dryer outlet, I clean it out (flex) yearly to prevent problems. Reattached flex on both ends, re-positioned dryer, plugged back in, and works great! Definitely fixed my problem. . . Replacing the drum by myself was a bit difficult. Still do able (there's a video on that also. . )

The tear down on the dryer was more difficult than the instructions and internet showed due to different models used. The kit was not identical to the original parts but close enough to work (I think). The biggest issue we had was getting the drum back in and placed on the wheels where it would turn easily. Overall the repair came together but it was a bit more involved and we anticipated going into the project. The actual noises were caused by the disintegration of the tensioner wheel which broke and was wobbling on the axel.

Ordered the fuse first hoping it was just that simple, watched the video for how to replace, first step was to take the back of the dryer off, well I order to take the back off I had to take off the Electrical Cord, as well as he top of the dryer. Only to find out he part I was replacing was not back there. Found the tech sheet attached within he dryer though, and as it turns out only needed to take he front bottom panel off. Without testing he continuity I was just giving this a shot, the Thermal fuse did no fix it, so I tried the high Limit Thermostat and Fuse kit still no luck. Took out the Element to find I was physically cracked in 2 pieces, replaced that and I was back up and running. And all parts were found in the bottom front panel of the dryer, so beware before you watch the video and take our whole dryer apart like I did.

Called a appliance place. They said it was a serious problem with master board and it was gonna cost 425.00 dollars. NO THANKS. Ten minutes to open ten minutes to find the problem. ( which was no were near the master board). Seconds to find and order the parts on partselect.com. got it next day. 15 to 30 minutes later my dryers running like it was brand new! Love it.

Replaced with parts orded worked fine for2 hours and quit heating again

My husband changed the part but part select was very helpful. With their free repair help site it made repairing a breeze! We will use parts select again and again. I did order all the parts we might have needed and only needed one. Now I will return the others.

First tried repairing the old idler by cleaning and lubricating the shaft. That lasted for about a week but the squealing returned. Ordered the part and had it in a few days. Replaced the idler wheel and it's been quietly running like new for several weeks now. Now wife thinks I'm Superman.

I removed the back of the dryer and then unscrewed the thermostat and fuse from the heating element shield and replaced with new ones. I simply reattached the back and did a test drying run. Good news, no overheating. Easy-Peasy