GEW9200LT1 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joyce from Holbrook, NY
- Parts Used:
- WP8577274
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
When using the dryer the cycle would stop and display E1 as the reason
Unscrewed the bottom panelof the dryer and located the thermistor through the schematic for my machine. Removed the old one and put the new one in the same way. No more E1 problems and all cycles now complete themselves.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from HUEYTOWN, AL
- Parts Used:
- W10837240
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Idler pulley wore out
Removed the back panel and saw that the idler pulley was worn out. It only took me 5min. To replace, it was very easy to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Great Bend, KS
- Parts Used:
- WP3387747
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
my dryer would not heat up any longer
I had already taken the coil out of the heating housing to check for a break in the heating element. I took this time to vacuum out all the lint inside the cabinet. I slid the new coil into the housing and reattached the wires. Plugged the dryer back in and turned it on to make sure the coil heated up. It worked so I put all the screws back in and fastend the front back on and were in bussiness!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from INOLA, OK
- Parts Used:
- 4392067
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Broken belt. Broken idle pully and replace 4 rollers
By watching the video it made the job much easier than I thought it would be. I was very pleased with the speedy delivery of the Dryer kit I had ordered. I had called a local repair facility and they wanted twice as much for the same parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorraine from Elk Grove, CA
- Parts Used:
- WP3387747
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Wouldn't heat
My husband said it was very easy and quick. We will recomend your site for sure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from langley, KY
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
gasket came off lent filter
i could not find this part anywhere locally,so i found this web site which had this part.i ordered this part and am very glad i did.i received it in 2 days.thank you very much.if you need anything check this place first,you will be very satisfied.
Was this instruction helpful to you?
Thank you for voting!
Dryer squeeching very loud
Took off back of dryer Undid belt from belt adjuster pulled and took off adjuster put new one on redid belt and put back on dryer. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hal from Edgewater, FL
- Parts Used:
- WP3387747
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
no heat
unplugged from elect power.took off front lower panel.removed heater heat shield w/1/4 in nut driver,could see heat element. it looks like at thin metal twisted phone cord. i used a continuity tester to establish if there was a break in it. there was. i removed 2 1/4in screws on the right side of the element,marked wire placement slid out old element & slid in new one put screws back in connected wires,put heat shield back on . tested dryer ,ok good to go put on front cover.!!!!! PS sears parts wanted 15$ more
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from Chesapeake City, MD
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
my teenage son was messing around and got into the dryer and broke the door catch and bent the door.
removed the catch and the pin and replaced it. We were sent a couple different sizes so we tested the one that looked like the closest match. I think the pin was made with different thicknesses of metal. Worked great and saved us from having to get a new dryer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Andalusia, AL
- Parts Used:
- 279973
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Dryer not heating
Open breaker and ensure power was off. Checked heating components for continuity.Found thermal fuse had an open circuit.Replaced High limit thermostat and thermal fuse.Now is a good time time check for free flowing vent piping.I discovered mine was crimped below the floor and caused lint build up and obstructing the flow which could have led to the thermal fuse blowing.I replaced the vent piping as well.My wife says the dryer works better now than it ever has.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theresa from Norfolk, VA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The old door catch failed. Clothes won't dry with door open !
Old door catch came out, new one slipped in. All works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Manuel from Key Biscayne, FL
- Parts Used:
- WP3387747
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Not heating
So simple.... I have no idea how to fix anything but I took a crack it. Looked inside and pulled out the resistor. I noticed the coil was broken so I replaced it with a newn part and reinstalled it. Worked like a charm. Saved myself alot of money!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Yorba Linda, CA
- Parts Used:
- WP8182050
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken timer knob
Was very simple repair, and just required pushing the new knob on by hand pressure. The part was ordered and it was delivered in two days, and I will not hesitate to order from this company again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laurie from Natick, MA
- Parts Used:
- WP3392519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer was working but not generating heat.
I was reluctant to call a repair service. Typically when an appliance is as old as my dryer (14 years old), service people encourage you to replace, not repair. I had replaced the dryer's motor within the last 5 years and believed my dryer still had life to it. At first, I tried cleaning the lint build up from the dryer cavity and hoses. This worked but only for a couple of days. After reading other successful repair stories on the website, I decided to try replacing the thermal fuse. It was so easy. The part was easily identifiable. It was just a little hard to yank off the connecting wires. Good as new and no service call.
Was this instruction helpful to you?
Thank you for voting!