XCEM2765FQ0 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- juan from los angeles, CA
- Parts Used:
- 279570
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken door catch. door wont close properly
i watched the video from Part Select. did exactly as seen and presto it was easily done. never could've done it without Part Select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- margery from Lake Spivey, GA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
the door catch was broken and I was using duct tape to close the dryer!!
This was a classic easy repair and I am sure saved us bundles on a service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Port Arthur, TX
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would not latch closed when shut
Reviewed the video showing how to remove the bad-order part and install the new part. No problem. Installing the new part was exactly what was shown in the video on the web page.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Millinocket, ME
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Door would not latch
I pulled the old latch out of the catch and installed a new one. It just popped into place. The job could not have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Colby, KS
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My dryer door would not stay shut.
I removed the old door catch by using a screwdriver to pry it out, then I popped the new door catch in its place and it snapped right in. It took less than 5 minutes to do the whole job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Encino, CA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken dryer door latch.
Fantastic site and service !!! Using your site, I i'd my needed part in about 10 minutes. I received my Whirlpool dryer door latch part from you in less than 12 hours. Per your internet site instructions, I replaced the part in a few seconds (just popped it into the slot) and my wife had a working dryer for her Sunday wash. I would have been out $55 and 4 to 7 days waiting for a service call if I had used my home warranty service contractor. Using your service, the part(s) and shipping were just over $12.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Edina, MN
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old Part Broke Off
Took 5 seconds, just snapped in the slot, didn't need any tools.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from Riva, MD
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
dryer door wouldnt latch shut
ordered new latch kit and repaired, very easy thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Lowell, MA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door latch/ catch completely shattered
Snapped latch into existing hole in 2 seconds. The pin that goes into latch was still intact. That's it ,real simple. The only problem I will hopefully not have in the future is the the mico-switch which is just hanging in there, the switch works but the lever that extends out from the face, that works with the door is partially broken off and the switch is no longer available on your parts list. The appliance is twenty-one years old. I am very happy with your service and I received the parts the next day, after I ordered them and I will be buying more parts in the months to come. This time it will be for my Kenmore gas stove and then a Kenmore refrigerator door hinge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
The grill cover to the dryer vent broke in half
I ordered the part with the manf. # BUT upon installation I found that the new part was slightly different than the old part therefore not allowing me to screw the new part to the inside of the dryer - I was able to find longer screws that would work but took me an hour to figure out what the issue was and then resolve the matter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Sonora, CA
- Parts Used:
- W10470674
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
Needed to vent the dryer to the left side
The kit turned out to be missing a 7.40" 4" diameter vent that was needed so ending having to get my plumber to use what was there with a "cut and paste" job - took him over an hour. He did say that had the right piece been there, it would have been easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harlon from Browns Summit, NC
- Parts Used:
- W10470674
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Needed to vent to side due to space requirements
Upon receipt of the new vent kit, I removed the dryer from its location and took it in to the garage. This facilitated a roomier work space. The directions were easy to follow and the work to be performed was very easy in this setting.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julian from San Antonio, TX
- Parts Used:
- 4392067
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Noisy/Rattleing Tumbler
First i did some research on the internet approx.1yr ago.Just in case any problems like this or any other kind of problems should arise which it did.The whole thing is Easy all you have to have is some basic knoledge of how things work.All of this came "OFF" in (4) sections.After installing everything back it was as "Quiet"as the day we purchased it.Good for another 5yrs.Retired welder & "J.O.A.T.Julian San Antonio,Texas
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Walkerton, IN
- Parts Used:
- 4392067
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer was noisy. Rumbled and squeaked as tub went around.
I highly recommend the videos on this site for repair information. It wasn't exact for the age/model of my dryer but very close. Remove the top panel and then the control panel. Remove the lower front panel and finally the door and main front panel. Unloop the belt from the motor and remove the drum. I found one of the drum rollers was bad, which was causing my problem, but I replace all 4 rollers, the belt, and the idler wheel. Sounds like it did when it was new! Find the video for your model and watch it!!
Was this instruction helpful to you?
Thank you for voting!