CSP2860TQ0 Whirlpool Dryer - Instructions

Checked on your website for common problems w/this model dryer,highest probability was the thermal fuse being blown,so I ordered one & checked the vent for being plugged,no problem there,removed the back of the dryer replaced the fuse(very easy to do)put everything back together & started it up...all set now.Thanks for your help

I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.

removed cover then pulled wires with a plier, unscrewed the fuse and installed new fuse then put back cover plugged in power cord, fired dyer and run dryer for 2 minutes and felt warm air coming out of the exhaust.

I guess you could say I went through the process of elemanation, first I replased the thermostat,removed 2 screws pulled off 3 wired with a pair of pliers put them on the new one, still no hot air so I replaced the fuse, took out 1 screw removed 2 wires and placed them on the new fuse, still no hot air, finally I replaced the thermal cut-off switch and WOW that was it hot air was blowing again, the process was very easy I ordered everything from parts slect and they were here the next day, only had to take the back off the dryer with a nut wrench, locate the thernastat, fuse and thermal cut-off which was just above the heating coil I removed 1 screw pulled off 2 wires and place them on the new one. very easy and the repair storys really helped locating the problem

So I opened the back up, and looked down the flame shoot and I could see that the igniter was never glowing red. (You can actually see the red glow of the igniter when its working right, then you here the solonoid click and flame. But again all this when its working correctly.) So anyway, no heat no glowing red.

I took the voltmeter out, grounded 1 lead and just followed the voltage (using the schematic provided), through the switches, yada yada trying to trace how far it got.

Voltage got to 1 side of thermal fuse, but not to other side. Bingo. Disconnected fuse and did continuity check - open. All of this took diagnosing took 1/2 hour to hour. Not really counting toward fix. Ordered the part at parts select. Put a jumper over the fuse so that clothes could still be dried (probably not recommended but it works). Part arrived in 2 days. Didn't even put the back panel on.

The part is right on the back. 1 screw, 2 space terminals. Takes all of 3 minutes to replace. Then another 5 minutes to put the back panel on and vent hose back on. Most of that is because you are working in a cramped space. (I don't have the biggest laundry room.)

Can't beat parts select!

Parts select + a little know how, saved me about $400.

Dropped new filter in.

I removed the back of the dryer, removed the single screw holding the fuse in place and checked it for continuity. It didn't work, so I placed an order and 3 days later I was back in business. the replacement took about five minutes.

this was a super easy job! i unplugged the dryer, removed the back panel, located the fuse on the bottom left side, replaced it, put the panel back on, plugged it back in and IT WORKED! this was the first appliance repair job for me and i am so glad i found this site. it probably saved me $100.00 or so doing it myself. thank you!!!

My wife and I thought our dryer was done and we were looking at a large replacement costs. We started googling and found this site and watched the video. We are were 99% sure it was the thermal fuse. We received within 2 days and thought we would be in there for over an hour. Turned it was less than 10 minutes, we watched the video clip on how to install on our laptop as we did it.

We will always be buying parts from this site and have told a ton of friends/family to check this site out.

It saved us so much money!!!!

I opened the front lower cover to get the schematics. Looked for the most probable part that was bad. Then traced wiring from the gas solenoid to find the thermal fuse.
I opened the back. Took the two wires off the thermal fuse and put my Ohm meter from terminal to terminal. As I got no reading, I ordered a new fuse. It took about 5 minutes to replace and button the dryer back up. This is the second time I have had to replace this fuse.

I replaced the male end first hoping that a change in the female part would not be needed. Unfortunately no. I used needle nosed pliers to pry the male part out and pushed the new part in. The female part of the door catch was more difficult. I didn't do it in "textbook" form, but got the job done with pliers and a screwdriver. Worth every penny to fix correctly instead of rigging it. Do it!

Got my parts very quickly.
Popped out the old door latch with a screw driver and pressed in the new one.
Very simple.
Thanks Parts Select.

The only thing I had to do was hammer the catch inside the square fitting and presto it was done. It took me less than 3 mins. I thought I might of needed instructions, but it was really simple. Even a guy can do it. (smile)

Took back panel off dryer, unscrewed old part, put on new one. Easy fix. Dryer works great again.

Pop out the old latch and replaced with a new one