WGD97HEDU1 Whirlpool Dryer - Instructions

Sensor is in the front lower left. Gas off, electicity off. Removed two screws for the filter, pry/lifted the top up and taped it too the overhead cabinet, removed two screws inside top of front panel, lifted pandel with door closed staight off. Two screws to remove the flame sensor braket. unplug the old sensor install the new one and reverse everything. With others suggestions I purchased temperature switches etc. but the radiant flame sensor was the problem. I now have some spare switches for future. Excellent company and very quick service. Oh, Sears wanted 200.00 just for the service call, I live rural.

Purchased the dryer maintenqance repair kit. Very simple to do. Easy to follow instructions. Took less than an hour. Everything I needed was in th kit. Did not have to run to home depot for anything.

For the Ignitor - As involved as taking the dryer completely apart sounded, it was super easy. 1-take out the lint trap and remove the two screws there. 2-Pop open the top with a screw driver and swing the top completely over/back. 3- remove the two screws holding in the front panel and remove the panel. 4- loosen the belt by pushing on the tension roller under the drum on the right and remove the drum (its super light) use the belt as a handle. 5- remove the screw holding in the ignitor and replace it with the new one. Be careful to not touch the new ignitor. Then go backwards putting it back together.

Removed top and back covers. Placed new pulley and retaining clip in place. I had to remove a couple of drum supports to put belt on. Probably didn't have to remove top.

I disassembled the dryer, replaced the pulley (which was noisy), and the belt.reassembled, only to find out that the drum would not turn freely. checked all my procedures and kept having the same problem. Finally after 3 frustrating hours, I took the back off and noticed that idler arm was tight against the motor shaft, because the too short belt didn't allow for the clearance needed. Had too take everything apart ,another hour, went and found one at our local repair shop, reinstalled everything , after another two hours runs fine. would appreciate a refund. And please check your part numbers in the future. Would hate to have someone else go through what i experienced.

1.Unplugged the connections to dryer door
2. Removed dryer door, front cabinet,popped off the drum belt (this is done by feel),unplugged the drum from cabinet, removed drum, all to get to the gas element inside at the bottom of dryer.
3. Unplugged the connection to the element, then removed unit to get to the burner parts.
4. Replaced the natural gas burner element with the LP gas element.
5. Re assembled dryer and tested.
*Note: Actually my son did the work while I read the very easy to follow directions. Since neither of us has disassembled a dryer before, the thought of taking a brand new dryer all apart was more daunting than the actual task.

Super easy to repair...I had to idea how to get started; but after watching the video from your site it was a breeze. Thanks for having "how to repair" videos on your site.

Repair kit came in 2 days..fantastic..thank you so much....with new rollers, belt and tension roller she works like new

First, let me say the t videos are excellent. Check them out if you haven't already.

I came across the video on diagnosing the causes of odd dryer noises. After watching that, I decided that the issue was probably a drum roller.

I took a chance and ordered the maintenance kit to avoid having to take the dryer part to confirm the diagnosis and then put it back together again while waiting for the parts to arrive (BTW - the parts arrived within two days of my ordering them) .

Even if you know your issue is only the roller, I recommend getting the entire kit. It takes no extra time to replace the drive belt and the idler pulley while you have to dryer apart and I consider it good preventative maintenance.

Definitely watch the how-to video PartSelect provides on how to perform the repair using the maintenance kit. It's very clear and very helpful. I'm not sure I could have figured out how the belt fit through the idler pulley without it.

As video shows, the repair is pretty straightforward. As others have noted, you'll likely find a couple of dollars in change and a goodly layer of lint in the bottom of the cabinet. Have your shop back handy.

It seems kind of silly, but I found the hardest part of the whole repair was getting the front panel to slide onto the two bottom clips that support it.

One thing to watch out for are two small metal clips surrounding the screw holes at the top of the front panel. The nut screws that hold the panel in place screw into these, not the panel itself. After I struggled to get the panel in place I realized that in the process I had knocked the clips off and so had to remove the front panel again in order to retrieve the clips from the bottom of the cabinet. Minor frustration. And with all the practice I had the first time around, the panel went on much more easily the second time :-)

It was very gratifying to plug the dryer in, turn it on and have it run perfectly. Better yet, it impressed my wife.

So I was unable to get my model number so I took the hinge off the washer and was able to order the part. Before removing the hinge I used a marker and marked the hinge location on the washer. Once I got the part I removed the T15 screws on the inside part of the door and separate the pieces. I was able to remove the white tube for all 4 of the pins and put them on the hinge. I installed the hinge an then i put the front door pieces back together again while it was laying on the floor. I though I put it in wrong but I was correct. Once i had the hinge on the door and the door reassembled, I was able to attached the hinge to the washer. The hinge comes off the washer by pushing up on it and to reinstall you push down. I tighten the 4 T25 screws using the marks on the washer and the door is alligned correctly. I am able to close the washer door with one finger instead of my whole hand.

I simply followed the video and apart from a couple of areas that were not relevant to my model, everything went exactly as illustrated. The video is excellent and made the repair so easy.

The only issue I experienced was being short two rollers, as the parts diagram did not clearly show that there were two rollers in the back and two in the front.

A kit, with its own part number should be prepared that would show 4 rollers and belt as the recommended required parts.

It was an easy fix, I just did half the install a second time.

Unplug dryer. Remove the front bottom panel of dryer 2 screws, then unplug wire connector to the old igniter then unscrew one screw holding ignitor then wiggle out. Open new igniter wiggle back in place insert screw tighten, (getting this screw back in is a little hard) replug wire connector to new igniter replace front panel with two screws. Plug in dryer and there you go drying clothes again. Wife all happy again.

Disconnect power supply, remove power cord from dryer, remove dryer vent tube from dryer, remove 2 Philips screws from power connection on dryer, remove nuts from back of dryer, remove back of dryer. Locate idler pulley at bottom of unit at the rear of the motor, pull pulley back to loosen belt and remove from pulley, remove pulley retainer clip, remove pulley and rear washer from shaft and inspect shaft for wear or rust. replace washer and pulley (no specific direction to replace them, washer first then pulley). Reverse above procedure to reassemble. This is for a front load dryer, a top load dryer is different.

Cleaned out years of fuzz behind lower access panel and noticed where the igniter sits there is a metal tube about 1 inch in diameter. It had rust on the end and was starting to flake away. Found some helpful hints about how to test the igniter. Very easy, just used an ohmeter. Unplugged the 2 pin wire connector and checked for continuity. 1 lead on 1 pin and the other on the other pin., igniter side not the harness side from the dryer. A good igniter should read less than 5 ohms. I don't know the spec. exacttly, but it should not read open or infinite resistance. My meter read an open circuit. Removed the tube and igniter assembly, mine only 2 small bolts. I found the igniter element cracked. Ordered and installed igniter and tube assembly. This was a very easy install. 20 year old dryer works great and it's better than spending $500.00+ on a new one.

had to take front off of Dryer then was able to replace drum roller

Used the maintenance kit....followed the movie tutorial. I also used an empty gallon plastic container to support the front of the drum while stretching the belt over the motor pulley. For the rear drum rollers, before sliding them on the shaft, I put a light grease film on the shaft. After the repair, the dryer runs quieter.