WGD87HEDW1 Whirlpool Dryer - Instructions

Desarme la puerta y coloque la nueva con mucha facilidad, nunca reparé un electrodoméstico antes de este, seguí el diagrama que encontré en el sitio para elegir la pieza que se rompio

Disconnect gas line and vent hose,removed top and back covers to install belt.

This could not have been easier. The hardest part was tipping the dryer over on its' side.
Instructions:
1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor.
Insert leveling foot into the foot opening on the bottom of the dryer &
screw in with fingers until it is difficult to turn.
2. Use the adjustable wrench on the hexed foot (not the threads) to adjust to the desired level.
3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position.
4. Use a level, back to front & side to side, to determine if feet need further adjustment.
5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.

Before anything unplug the dryer
1) Remove the back panel to include electric cable. 2) Remove the lower front panel. 3) Remove top panel. 4) Remove control panel 5) remove door assembly to include metal frame and front panel of the blower housing. (much easier than trying to do this separately. 6) Remove drum belt by pulling back on the idler pulley (spring). 7) Remove drum. 8) Remove idler pulley retaining ring and pulley. 9) remove old seal on blower housing. 10) I added high temp grease to the pulley shaft and installed new pulley. 11) Install new blower seal. 12) Install drum and new belt. 13) Re-install all the panels.

Unplugged the Dryer first. Removed the two screws from the bottom panel using a 1/4 socket and removed the panel by pulling down and out. Reached behind the blower and removed the connectors from the old thermistor and then the thermistor itself by removing the two 1/4 inch hex head screws. Replaced with new part and after screwing back in, reconnected the wires and replaced the panel. From start to finish, it took me about 20 minutes.

I researched causes of the noise, zeroed it down to the idler pulley. I then got the dryer schematic and took the dryer apart after disconnecting the power and the vent. i did not have to remove the drum, the idler pulley was easily accessible once the top and back panels were removed. I simply removed the drive belt from tension off the pulley, removed the old pulley and installed the new one. Once finished the dryer was running whisper quiet.

I first tried replacing the Radiant Flame Sensor, which was located in a tight space and was very difficult to access. I finally gave up and called a handyman to replace it. That didn't fix my problem. I needed a new igniter. That was easy to replace, but it's fragile and I broke the first one...

I removed the top first followed along with removing the side bracket that holds the circuit board. I then proceeded with removing the bottom cover and front panel. I disconnected the front panel from the control board and was able to slide the front panel upward. The door and blower housing was a bit tricky to pull out without thinking I was damaging something. I then replaced all the seals and cleaned the dryer after removing the drum and belt. I also replaced the drum support rollers. Afterwards I put everything back together and had an "E1" error and I pulled the thermostat out and wiped it down from all the lint and dryer worked perfect after that. Dryer takes the right amount of time to day clothes and no more rumbling noise. The instructions videos were VERY helpful.

It was a lot easier then I thought. Just watch the tutorial of how to fix it on this website and you wont have a problem.

Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger

Disassemble dry. Put on new pulley wheel. Greased pulley wheel. Put dryer back together. Works great. Yours truly G.B.

pull the back off and replace the pulley.

I started by changing the part that had the highest percentage to solve this problem , the top three didn't work , the fourth part, the disposable thermostat, and the last one that could be done from the front worked.

Took back panel off, and it was really easy putting the new idler pulley in.

Seemed daunting but pull the front off and the drum is basically just perched inside on some rollers. You have to pull it out to really reach in and wrap the 96”+ band around it and to motor and don’t forget to tension it with tension pulley if you don’t see that if your belt broke!
Another bonus is after 10 years I got to remove the softball size fur ball rolling in the squirrel cage fan , big help on air flow!!!