WGD72HEDW0 Whirlpool Dryer - Instructions

Removed two hex screws from upper back clips. Removed 2 Phillips screws under lint trap. Used flat head screwdriver to pry up top on front right and left side clips. (FYI: top pry's up off retaining clips in front). Remove two hex screws on right and left front panel. Un-plugged wire harness front right side. Lifted up and removed front panel. This hold the drum in place. Simply removed drum, installed new belt, replaced the two drum wheels and put everything back together the same way I took it apart. 30 Minute project :)

I removed the base cover and cover over my lint blower. The thermal fuse is located on top of the blower housing. I removed the thermal fuse utilizing a small nutdriver and installed the new fuse.

Checked fuse with Volmeter, had continuity (acted as a short) not the problem. Disconnected Hot Surface Igniter 2 Position connector to check resistance for a range of 50-300 Ohms of resistance with Voltohm Meter. Meter read open (High Resistance). Removed Igniter by unscrewing 5/16" hex nut on igniter plate assembly and noticed silicon carbide element was cracked in the middle. Ordered a new igniter and noticed assembly was required. Be careful here as igniter element is fragile, also do not touch it with your bare hands. You have to lay down on floor to reinstall igniter assembly and you might want to practice anchoring the defective igniter to gain confidence. Finally with slow movements anchored new igniter assembly and turned on dryer. Watched igniter glow heating gas valve and heating gas flame returned. Dryer fixed for a few hours of study online and cost only $24, plus learned how the gas dryer works.

Took the old parts out and installed the new parts in , everything that you sent fit perfect!!!!!

Replaced 4 wheels and new belt

Ezee pezee lemon squeezee.

Took the back and top off of my front loader. I had checked on you tube for the problem and how to fix it and ordered the part. Just followed the directions on how to remove the old idle pulley and installing the new one. Dryer runs like new!

I watched the video or I would have likley just called a repair man. It took longer to clean behind the dryer than to install the new thermal fuse. After taking the back off the dryer is was as simple as changing a fuse. Dryer works like new for about $20 bucks and we avoided the hasle of getting a repair man, especially since we live in the country. Thanks for having a web site that is so easy to use and full of good information.

Took the top off and then front off and drum out . Replaced Drum roller and shaft support bolts.

Removed the dryer door, unscrewed lint vent.

Replaced the most worn drum wheel any lubed the belt tension arm pulley. The noise didn't go completely away. There are 4 drum wheels. I need to order 3 more wheels and the tension arm now.

My dryer would not start or turn. I first moved the timer to midway between start and end of a cycle and could hear the timer ticking, likely eliminating the timer as the culprit. I next opened the door, manually pressed the door-closure switch and pressed START to see if the heating coil was heating without the drum turning to see if it might be a motor issue. After no heat, I unplugged the dryer and removed the vent hose by loosening the clamp and then removed the lower back cover using a socket and ratchet. Using a multimeter, I quickly found an open thermal fuse. I tested the remaining components to see if they also required replacement (coil, thermostat, high temp sensor) - all tested good. Took a chance and ordered the fuse alone instead of also purchasing replacement thermostat as many advise - if you have not replaced in a while, probably worth doing now. I have replaced mine within a year or two and chalked up the issue to my kids not clearing the vent, so I went without the new thermostat. Model number was found by opening the lid - parts arrived incredibly fast especially for being around the holidays. Replaced the fuse with ease - there is a notch in one end that holds the non-screw end in place so it's flush. Plugged the dryer back in, selected a cycle and confirmed the dryer started and heated as normal. I then had my son open the dryer door to confirm the drum stopped turning. HERE'S WHERE IT TAKES A TWIST: When the door was open, the heating coil continued to glow red hot (faulty timer??) I moved selector to end of cycle and the glow stopped. (timer's good) I then moved the selector mid-way between cycles with the dryer door open and WITHOUT PRESSING START and the coil again glowed red. Disconnected power, disconnected coil and using multimeter, checked from coil input to case ground (any bare metal) and found one side of the coil to be grounded. I was able to removed the heating coil and locate where the coil was touching the case. I shifted the coil back into place, checked with meter (no ground this time), reinstalled and tested with no problems. Reinstalled the back plate and vent hose. Finally, had conversation with the kiddos about being gentle when moving the dryer and all was well. The thermal fuse portion took 15 minutes from diagnosis to replacement. The overall process (due to the additional grounded heating coil) took 30-60. With any repair like this, I usually recommend visually verifying the heat cycles on and off by carefully running with the door open and holding the switch. This will help you determine if you may have an additional faulty part that made the first one fail. (Most likely, thermostat).

The repair went well, using the whirlpool repair manual and looking at the video from PartSelect. The machine was a bit different than the one in both the video and the manual but that did not cause any problems. The only tricky part was to reinstall the belt "blind" behind the motor, easy to pinch your fingers and also get scratched by the sheet metal edges. To make it easier for that part I supported the drum with the old belt and a bungee cord to the garage frame so I did not have to hold it up and work under it at the same time. When the drum and new belt were in place I just cut the old belt, it was going to the trash anyway.. I replaced the belt and the tension pulley, witch was not turning easy and worn by the belt. I also put some grease ( SUPER-LUBE, www.super-lube.com) on all pulleys. It took about 2 hours because I am 78 years old and have heart problems.

I had two dryers, one was gas and the other was electric. The electric stopped heating. So I rolled out the gas dryer, but it was setup for natural gas and at this location, I only have propane. So I changed the jets to work with propane, in the process I broke the igniter, so I replaced that and that made the propane one work. Armed with the knowledge from that job, I took the electric dryer apart located the thermostat and replaced that and low and behold I have two working dryers. One for now and one for an emergency. I only have four screws left over!!!! Jim Cooke

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Performed current check to determine possible problem-then Able to go on line with partselect, extremely easy part description and selection, ordered, part arrived next day. Could not have went any better