WGD4985EW0 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carolyn from STIGLER, OK
- Parts Used:
- WPW10117655
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Push button wouldn't work
Still wouldn't work! Push switch returned to you but have not received a refund yet. The repair was very easy. Tracking # 1Z 2R5 3A2 03 0025 9453 for returned switch.
3
3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from East Earl, PA
- Parts Used:
- W10861225
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Handle on my Maytag Dryer broke off while opening
When the part arrived I opened it and just snapped it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marceline from SAINT PAUL, MN
- Parts Used:
- W10874409
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The lint screen had a hole
Just slipped it in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PATRICK from PALOS PARK, AL
- Parts Used:
- 279769
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drier would not heat up
i took off the back of the drier and with a screw driver removed the 2 screws and put the new part on
Was this instruction helpful to you?
Thank you for voting!
Dryer would not dry clothes no heat
Followed video you give on your web site very use full used putty knife to undo clips holding on the top lifted top unplugged wire for door switch undid two bolts with socket set lifted off front panel of dryer first changed heat sensor 1 screw unclip wire put on new sensor re clip wire bottom part of sensor goes into a slot line up hole on top put screw back and tighten for the igniter kit unplug wire clip remove on screw with socket set have to put new igniter on bracket with new screw included with kit be careful no to bang igniter when replacing it replace it with screw re clip wire replace front of dryer with two bolts replug wire for door switch close top for thermal fuse and thermostat internal- bias remove nine screws on back of dryer take off panel disconnect vent on my gas dryer had to shut off gas supply and undo gas line thermostat internal -bias and thermal fuse are easy to do thermal internal bias has four wires and one screw just replace wires the way they came off replace screw same with thermal fuse two wires one screw just reverse process be sure not to mix up wires replace dryer back with screws hook up gas line check for any leaks turn on gas supply hook up vent and you should be good to go test dryer hope this help someone like others helped me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Long Beach, CA
- Parts Used:
- WP338906
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
No heat...
Removed and replaced both the thermostat sensor and the ignitor. Tested thej dryer and it worked. Replaced the front panel and it was good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from BOILING SPGS, PA
- Parts Used:
- 4392067
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench set
My dryer was squeaking with an occasional thump
Watched videos on line on how to repair. Replaced all four Drum Rollers, Belt and Idler Pulley, cleaned out inside of unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from STONE CREEK, OH
- Parts Used:
- WPW10314173
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Dryer drum turned hard because rollers were worn
Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from HUNTSVILLE, AL
- Parts Used:
- 4392067
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Sqeeking noise fron old worn belt and rollers
Watched instructions, Ordered the kit and repair was fairly easy until the time to line up the cover over the fan wheel. That was difficult part. Would be best to have two people at this point to hold it and align the screw holes. Otherwise its was a fairly easy operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- barbara from SOUTHAMPTON, PA
- Parts Used:
- 279769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer ran but without heat.
Turned off my circuit breaker first. Removed back panel with a 1/4 nut driver. Replaced the dryer fuse first. Very easy but did not fix the problem. Watched how to videos to narrow down the parts I might need. Purchased the thermal cut off kit. Installed the High limit thermostat first. Tested the dryer, no dice. Finally installed the Thermal cutoff. BAM!! I have heat. Since this is an older dryer I did need to use some WD40 to loosen some of the connections. Total cost of parts including tax and quick delivery was $48.30. Fantastic. My old man told me it was unfixable. He was wrong. I WIN. This site is a great teaching site. Thank you!
Was this instruction helpful to you?
Thank you for voting!
Poor drying and took excessive amount of time to complete partially dried loads
Took back cover off. Cleaned out the lint that had built up inside the dryer. Replaced the lint trap housing and lint chute seals. Also replaced the drying vent hose. Works great now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from BUTLER, PA
- Parts Used:
- W10874409
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken lint screen
Exact part needed, fit exactly like original.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Afton, OK
- Parts Used:
- 49572A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
change from nat . LP gas.
Remove top then front panel kit goes on gas value 2 screws hold gas tube in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from Springfield, PA
- Parts Used:
- WP3392519
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver
No Gas Heat
I did what any novice would have done. I took the entire thing apart to get to the gas jet. I did not know about the thermal fuse until I got to the schematic behind the timer and controls. I was a tech back in the 70's and 80's and only worked on electric dryers. Back then I would remove the heater core and twist the coils together to save money. So I had no idea how a gas dryer heating unit worked. So now any one that reads this. You do not have to take the dryer completely apart, I did that for all of you. Just replace the thermal fuse on the back of the unit by unplugging that wires and removing the screws! It looks like a long white piece of plastic with 2 wires to it. You will find this under the full metal shield on the back of the unit. This should be about a 1 hour repair at the most!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Macomb, MI
- Parts Used:
- WP3392519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Whirlpool Gas dryer, run but no heat
I simply removed the rear panal of the dryer. Removed the two wires from the fuse at the rear of the dryer. Attached an OEM meter across the two fuse connections and had no continuity. Ordered a new fuse and recieved it in 2.5 days.Replaced the fuse,reconnected the wires and replaced the rear panal. Started dryer and it now blows hot air and runs like new. I can't say enough about PartSelect. Great diagnosis using their website, the delivery was fast and I recieved the correct part at a good price. Very satisfied, Thanks PartSelect. Fred F
Was this instruction helpful to you?
Thank you for voting!