WGD4800BQ2 Whirlpool Dryer - Instructions

Took back cover off
Disconnected part
Put new one in
Reconnected wires
Put back cover on

To verify that this was the needed part, I used a digital multimeter to confirm there was no continuity.

After researching and finding correct replacement unit placed order and waited to receive. Screen is located top of dryer so replacement simple and fit was perfect.

I looked at the parts breakdown to see how it cam apart.

I tore the dryer down,
1. removed the door
2. openned the top
3. removed front panel
4. removed fron bulkhead
5. removed belt and drum
6. removed back cover
7. removed the ductwork
8. removed the fan (this is the hardest part, it is very tight on the motor with left hand threads, there are flats on the (inside of the dryer)fan where the motor shaft goes into the fan for a wrench and you can put a socket on the front pulley on the motor. I ended up just knocking the center out of the fan and replacing it.
9. removed the motor and cleaned the entire unit
10. reinstalled everything in reverse order. Note:I went ahead and replaced the idler pulley and the rear wheels that support the drum, and put a new belt in (just about
everything that could fail) I spent about $200 to keep a $1200 dryer in service at least another 7 years.

Troubleshhot problem, used multimeter to verify current to motor. Once that i was sure motor was getting proper voltage, I used a meg-ohm meter on A/C motor windings and physically tried to turn motor and found that it was siezed. I then cleaned inside of unit inspected belt and drum rollors. Due to the cost of the items, I decided If I was going to replace the motor I should replace all moving parts, and install new belt. Everything went easy. WHAT WAS MOST IMPRESSIVE! was that the Parts people sent the correct parts on time the first time, with no hiddin charges. There web site should accurate diagrams of parts and internals of machine. I was really pleased and will use this service again. Thank you

Solution: electric motor replacement as the integral centrifugal switch lever (plastic cam) wears over time causing the start windings' switch poor contact. Took it all apart, (back panel, front and top) including lifting the drum out to completely expose the motor. Needed to wrench the plastic fan from the inside motor shaft. Tricky part was swapping the original pulley (6 rib belt, still good) for the one supplied for 4 rib belts. I needed to file another flat onto the other side of both motor shafts (old and new) to break them free, using a vice to secure the pulleys. The dryer works perfectly! It's a great dryer that can be repaired by a determined novice. The enclosed instructions were helpful, although if followed about cutting the original motor shaft to obtain its pulley might require drilling the shaft from the pulley = nonsense. Thanks again Parts Select.

Took everything apart, replaced the igniter flint, and still didn't get heat. Then found out the thermal sensor wasn't running a electrical current through it with voltmeter and just replaced that, now it we have heat again!

I had an issue where I was not getting any power to my ignitor. After replacing the ignitor with a fresh one, the problem persisted. Next, I went hunting all the fuses and therrmostats for continuity. All seemed fine. So finally I decided to jump the flame sensor which is located on the outside of the flame tube. WHALLA! It ignited the glow plug. So with one 1/4"" nut driver I removed the single bolt from the unit, then I used a pliers to remove the two wires from the old unit. I replaced the sensor with Tue new unit and all was well. It took less than 5 min once I diagnosed the problem.

just slide the new filter in.

My 80 series Kenmore dryer wouldn't start so I looked online for a solution to the problem. One of the sites I found stated that the problem could be as simple as a thermal fuse if other potential issues could be ruled out. I ordered the part on a Monday from PartSelect with standard FedEx ground shipping - stated it could be 3-5 business days. To my amazement, the part arrived the next day! Awesome!!! I watched the video on the PartSelect site to make sure I knew how to fix it, then followed the easy instructions. All I needed to do was use the nutdriver to remove the back cover from the dryer, unplug the two wires going into the thermal fuse, remove the old fuse, and pop the new one in. Then I just plugged the wires into the new fuse, replaced the cover and voila, the dryer worked like a champ! Thank you PartSelect for saving me a needlessly high repair bill!!

Remove back panel n u can see the sensor and easy to replace thanks to the print out i was provided love this website

I watched all the videos with Steve. He was very helpful in his presentation of the repairs. Due to the age of the dryer every thing was replaced and was very easy to do. Thank you Steve and PartSelect for making these repairs possible and easy

At first I was advised to replace the temperature overload sensors, which I did but didn't fix the problem. After adding the additional information that the dryer would run to full cycle as long as the Start switch was held in I was advised to replace the Start switch.

It wasn't obvious from the wiring diagram, but if you remove the Start switch and look at the side it shows it contains a solenoid holding circuit that keeps the switch in the "on" mode as long as there is a feedback signal from the temperature overload switches. So if the dryer will run to completion if the switch is held in, replace the Start switch. If it still stops mid-cycle, replace the temperature overload switches.

The replacement videos were spot on as far as clear and easy to follow instructions for the repair, and all ordered parts were delivered very quickly.

Thanks for your help PartsSelect!

Followed instructions from video, just removed lint collector, dryer top and front panel, removed broken belt and old idler pulley. Vacuumed and cleaned up inside dryer.installed new pulley and rib belt according to printed instructions,installed new dryer duct and new clamps. Saved myself huge service call or having to buy new dryer.Will be checking with this site on any future repairs instead of calling a repair service. Your video made it real easy to repair.and I am 77 years old.. Bob

First I did a search on dryer repair. Found a website that described easy things to check with an ohm-meter. I then performed the continuity checks on the items and found the high-limit one was open, in other words, no good. It works similar to a fuse. All this was done after removing the back panel, just a few screws. The reason it exceeded the high limit, possibly because I never opened the back up and cleaned it. Found out it should be done every couple years. My vent line had a hole in it and was letting lint get drawn into the heating element, could have been a fire.

My Whirlpool dryer had no heat. I removed the back panel and within minutes diagnosed the problem to a blown thermal cut-off fuse. I ordered a thermal cut-off kit on a Sunday night and had the parts at 7:30am Wednesday morning. Total time for diagnosing and repair was no more than 15 minutes. PartSelect saved me a ton of money and aggravation!!! AWESOME!!!!

Gary