WGD4870BW0 Whirlpool Dryer - Instructions

Was not sure what was wrong but the Part Select site allowed us to view other repair issues and solutions. We ordered the kit, it arrived the next day (how is that possible) and easily put the parts in and chaching...money saved and dryer works better than ever. THANKS PartSelect, we give you an eleven and we will recommend you to everyone.

Unplug dryer from mains. Remove the back of the dryer. Thermal fuse is located on the left hand side near the bottom as you face the back of the dryer. Remove fuse and connect new fuse. Never repaired an appliance before and this was so easy!

For the Ignitor - As involved as taking the dryer completely apart sounded, it was super easy. 1-take out the lint trap and remove the two screws there. 2-Pop open the top with a screw driver and swing the top completely over/back. 3- remove the two screws holding in the front panel and remove the panel. 4- loosen the belt by pushing on the tension roller under the drum on the right and remove the drum (its super light) use the belt as a handle. 5- remove the screw holding in the ignitor and replace it with the new one. Be careful to not touch the new ignitor. Then go backwards putting it back together.

Be very careful of burrs on the edges of the steel inside the dryer. I cut myself badly when reaching into unplug the switch.
Procedure: Lifted the dryer top by pulling forward and rotating front up. Removed 2 philips screws holding the switch at the door. Reached into dryer and unplugged bad switch. Inserting small blade screw driver at the edge helped release the plugs detent. Installed new switch using reverse of above.

Unplug dryer. Remove the front bottom panel of dryer 2 screws, then unplug wire connector to the old igniter then unscrew one screw holding ignitor then wiggle out. Open new igniter wiggle back in place insert screw tighten, (getting this screw back in is a little hard) replug wire connector to new igniter replace front panel with two screws. Plug in dryer and there you go drying clothes again. Wife all happy again.

Took back cover off. Cleaned out the lint that had built up inside the dryer. Replaced the lint trap housing and lint chute seals. Also replaced the drying vent hose. Works great now.

First i removed the rear panel on the dryer.the removed bothe thermostats that were on the blower housings.unpluged all wiers and installed new thermostats.reinstalled the wiers in there proper locations...note to log the location of the wires when removing from old switch.reinstalled the rear panel and hooked dryer back up and test.

Perfect!

Followed the video .... Also installed another part. which was a kit. the video here showed the third wire being installed. The video on repair clinic did not show where to attach the third wire (orange wire). The Kit and the Thermostat was installed with 25 mins. Thanks

Cleaned out years of fuzz behind lower access panel and noticed where the igniter sits there is a metal tube about 1 inch in diameter. It had rust on the end and was starting to flake away. Found some helpful hints about how to test the igniter. Very easy, just used an ohmeter. Unplugged the 2 pin wire connector and checked for continuity. 1 lead on 1 pin and the other on the other pin., igniter side not the harness side from the dryer. A good igniter should read less than 5 ohms. I don't know the spec. exacttly, but it should not read open or infinite resistance. My meter read an open circuit. Removed the tube and igniter assembly, mine only 2 small bolts. I found the igniter element cracked. Ordered and installed igniter and tube assembly. This was a very easy install. 20 year old dryer works great and it's better than spending $500.00+ on a new one.

Take out 2 philips screws in lint trap holder on top. Use flat screwdriver to pry up front left and right of dryer top near outside edges and tilt up out of the way. Remove 2 push-on AC connectors on door switch and remove plastic clip holding wires to dryer's front top metal edge. Remove (2) 5/16" sheet metal screw on inside top left and right edges to free up front panel. Lift front panel about an inch and it'll then pull off. It helps to have a second person to help hold or remove the drum at this point. It took 3 times for me to guess right on the squeak. First time I replaced the belt, second time I replaced these rollers, third and final time I replaced the idler pulley, the shaft of which had worn completely off so clearly i can't figure out how we didn't see (or hear) it the first two times! Dri-Slide lube helped stop the squeaking the first two times, but it always returned until this time, now I have a thoroughly rebuilt dryer for the next generation! (PS vacuum out the bottom of the dryer while it's open to remove both lint and greasy roller shavings - do this FIRST and you'll have cleaner hands & clothes!)

Removed the Lint filter, then lifted top panel and rested the panel against the wall.
Disconnected connector attached to the door panel.
removed screws, from both side of door panel and lifted door panel up and out.

Moved Idler pulley to the right taking tension off the drum belt, lift the drum out with the drum belt.
removed old drum felt seal and removed old residual glue, reglued and installed new Rear Drum Felt Seal.
Installed new Idler pulley Assembly and reassembled in reverse order.

The first thing I did was call my friend Donnie who manages some apartment buildings and who is always complaining about fixing things and getting the right parts to fix things. He told me what to order from PartsSelect and when the parts got here I called him up and he did the repair work.

He was reluctant to do the work at first but after he found out I had ordered the parts from PartsSelect he was happy to do the work. "Their parts are always right and they always work," was what he said after he had my dryer working just like new. So if you know nothing about fixing things and buying parts just call PartsSelect and you will be fine. Just ask my friend Donnie!!!

I called an appliance repair company to do a diagnosis and was told the timer would need to be replaced. Parts and labor was quoted at $290. The dryer isn't worth that much. Found a video on this site on how to replace a timer for my model of dryer. Ordered the part for $116 and replaced it myself. The video instructions were exact step by step.

Removed and replaced both the thermostat sensor and the ignitor. Tested thej dryer and it worked. Replaced the front panel and it was good to go.