CED9160GW0 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer had no display.
Replaced all 4 sensors. Still no display. Ran my thumb across all control buttons several times. Machine showed life. Looking good, but low heat. Replaced the heating coil, and now we have a new, 13 year old machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Baltimore, MD
- Parts Used:
- WP3392519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Dryer would not start
Longest time needed was to determine what cause was. After that ordering part from PartSelect was very easy and saved me money. Part arrived before time given, part was correct and installed without problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from UPPR MARLBORO, MD
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Broken dryer door catch
Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theodore from Tyler, TX
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer door wouldn't catch, catch was broken
took the cstch reciever out, with my fingers, pushed the new one in, snap lock fit.......couldn't be better, like repairing a model T ford.......
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james petrie from Stoughton, WI
- Parts Used:
- WP3392519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
no heat in the dryer
after removing the back panel (5 screws) i replaced the heating element, (about 15 minutes, after vacuuming all of the lint and dog hair), replaced the panel, but still no heat. removed the back panel again, and replaced the thermal fuse. (2 screws, 5 min.) still no heat, so on to the thermostats. (there are 2, both in easy reach). i replaced the one in the heating element housing first, as this made sense. (it has a red stripe across it, so they can't be confused), replaced one connector, which the new part requires, buttoned it up, and presto!! the dryer works just as new! all told, i have less than 100.00 with all of the new parts. the longest part of the whole thing was cleaning all the lint and debris out first, which you absolutely must do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from SCOTTSDALE, AZ
- Parts Used:
- W10120998
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
Torn filter seal
Remove old filter, throw it away, replace with new filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from ENDICOTT, NY
- Parts Used:
- 279570
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
broken door catch
Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from HUDSON, MA
- Parts Used:
- 279570
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
broken door catch
I followed your short video and found it very easy to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gloria from LINCOLN, NH
- Parts Used:
- WP3392519
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
dryer shut down wouldn't run
took off back, took out 1 screw of thermal fuse. pulled off 2 wires. put on new thermal fuse put back 1 screw and plugged. in both wires. plugged in dryer to make sure it worked. threw in some wet clothes to make sure it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from MALTA, NY
- Parts Used:
- WP3392519
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Dryer runs but has no heat
Found multiple videos on how to diagnose the problem. Parts plus showed me that over 50% of the time the problem was the thermal fuse. I put a jumper wire between the two connections on the thermal fuse to see if the dryer would fire up. Sure enough it did. Bought the $10 thermal fuse and changed it in less than 15 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from FOSTER CITY, CA
- Parts Used:
- WP3392519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench (Adjustable)
No heat in Dryer
The Termal Fuse did not solve the problem. Ordered a heating element so I hope its that
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theresa from HICKORY CRNRS, MI
- Parts Used:
- WP3392519
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
No Heat
Dryer works - thanks to a new fuse. Glad I tried this before just buying a new one. Video for my model indicated the fuse was located in the back and actually it was difficult to get to in the front. So extra time was wasted trying to get to fuse in the back. Thank you for the part!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DW from ALVIN, TX
- Parts Used:
- WP8577274
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
F-26 Fault message
Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger
Thank You.
DW Pranger
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAUL from ARLINGTON HEIGHTS, IL
- Parts Used:
- WP3392519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer wouldn't heat
It took me 5 minutes to find PartSelect's site, read the comments about the most common problems and identify the solution. The exploded views were a great assist, as it wasn't obvious where the thermal fuse is located or which access panel to remove.
It took less than 5 minutes to remove the rear panel and install a temporary jumper to verify the blown fuse was the only issue. With the new fuse in hand, replair took another 5 minutes.
A word of caution to anyone replacing is fuse - I found that the exhaust vent pipe to the wall was full of lint and nearly blocked. This is a potential fire hazard. While enough air was passing through the flapper vent to make it look like it was OK, the exhaust resistance is what caused the overheating and made the fuse blow.
I spent more time cleaning out the vent pipe than replacing the fuse, for a total of 25 minutes. I strongly urge all dryer owners to physically inspect the exhaust duct annually.
PS Drying time has decreased by 30-40% since the repair.
It took less than 5 minutes to remove the rear panel and install a temporary jumper to verify the blown fuse was the only issue. With the new fuse in hand, replair took another 5 minutes.
A word of caution to anyone replacing is fuse - I found that the exhaust vent pipe to the wall was full of lint and nearly blocked. This is a potential fire hazard. While enough air was passing through the flapper vent to make it look like it was OK, the exhaust resistance is what caused the overheating and made the fuse blow.
I spent more time cleaning out the vent pipe than replacing the fuse, for a total of 25 minutes. I strongly urge all dryer owners to physically inspect the exhaust duct annually.
PS Drying time has decreased by 30-40% since the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mary from Maple Plain, MN
- Parts Used:
- WP3392519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dryer was totally dead, had power to the outlet.
I studied the wiring diagram on the back of the dryer. I diagnosed a bad thermal fuse (no continuity). Found the part online at Part Select. The part came a few days later and I was back in business. Great Service.
Was this instruction helpful to you?
Thank you for voting!