WED99HEDW0 Whirlpool Dryer - Instructions

we received the two heating element wires in 3 days and connected the heating element with no problem works great.

Started at the top by laying back the control panel, then I removed the top panel, then the front panel, next the drum and the broken belt. before I put it back together in reverse order, I vacuumed the inside of the dryer and the exhaust vent

(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple to get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.

had to take front off of Dryer then was able to replace drum roller

So I was unable to get my model number so I took the hinge off the washer and was able to order the part. Before removing the hinge I used a marker and marked the hinge location on the washer. Once I got the part I removed the T15 screws on the inside part of the door and separate the pieces. I was able to remove the white tube for all 4 of the pins and put them on the hinge. I installed the hinge an then i put the front door pieces back together again while it was laying on the floor. I though I put it in wrong but I was correct. Once i had the hinge on the door and the door reassembled, I was able to attached the hinge to the washer. The hinge comes off the washer by pushing up on it and to reinstall you push down. I tighten the 4 T25 screws using the marks on the washer and the door is alligned correctly. I am able to close the washer door with one finger instead of my whole hand.

I simply followed the video and apart from a couple of areas that were not relevant to my model, everything went exactly as illustrated. The video is excellent and made the repair so easy.

The only issue I experienced was being short two rollers, as the parts diagram did not clearly show that there were two rollers in the back and two in the front.

A kit, with its own part number should be prepared that would show 4 rollers and belt as the recommended required parts.

It was an easy fix, I just did half the install a second time.

Replaced power cord, terminal block, and all melted wiring. Checked the thermal fuse for zero resistance.

Checked this site for most likely needed parts and ordered. Located full repair manual inside unit after removing lid. Followed instructions in manual to take apart and remove the drum; took pictures at each removal step and used pill organizer to keep screws in correct order and quantity. The metal cylinder in the center of the idler pulley had ground away so the idler pulley with bracket was replaced. (There was a lot of metal dust that had to be cleaned.) One of the rollers did not turn smoothly so that was also replaced. After putting drum back in, reversed the steps to reassemble and referred to photos to make sure did in correct order and did not forget anything.

Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.

Watched instructions, Ordered the kit and repair was fairly easy until the time to line up the cover over the fan wheel. That was difficult part. Would be best to have two people at this point to hold it and align the screw holes. Otherwise its was a fairly easy operation.

Watched videos on line on how to repair. Replaced all four Drum Rollers, Belt and Idler Pulley, cleaned out inside of unit.

Just like the video, just followed the video
Thanks,

I removed the bottom access panel, with 2 hands i reached in behind the blower, i released the belt, i used a screwdriver to pop the retainer from the pully spindle, i removed and replaced the pully, i snapped the retainer back on and replaced the belt. I made sure the belt was on track and all was good. I put the bottom panel back on, it took all of 5 minutes. The hardest part was the retainer clip faces the rear of the dryer so you have to feel it. Also , the space is tight, use a smaller flathead screwdriver to get behind the clip, it will pop right off.

Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair

Replaced 4 wheels and new belt